Abstract:Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, Ahead of Print. Aluminum alloys are widely used in various industries due to their as low density, high strength-to-weight ratio, and good corrosion resistance. However, their wear resistance is often inadequate for certain applications. Utilization of industrial waste materials, such as iron slag, as reinforcement in aluminum alloy matrix composites offers a sustainable approach to material development and waste management. The utilization of industrial waste materials for aluminum alloy matrix composite fabrication offers a waste utilization to material development. The loading of this reinforcement varied from 0 to 15 wt.% and different particle size range (220-140, 140-70, and 70-0 μm). A microscopic analysis indicated that the iron slag particles are spread uniformly inside the metallic matrix. There is also a reduction in the size of primary silicon, as well as morphological changes (acicular to globular shape). The wear behavior was calculated using a pin-on-disk wear set up in accordance with ASTM G99 standard. The composites were employed to dry sliding wear test under various operating conditions such as applied pressure (0.2–1.4 MPa), and sliding distance (0–3000 m). The 15F composite outperformed all other composite samples in terms of wear rate under all working conditions. When compared to the base alloy, it demonstrated a remarkable 67% drop in steady state wear rate. The enhancements in wear performance for the 15F composite were attributed to the effects of Fe slag reinforcement. The inclusion of iron slag particles induced strong interfacial bonding between matrix and reinforcement particles improving the durability of the mechanical mixed layer developed during relative motion. Importantly, the wear rate parameters of the 15F composite were similar to those of the brake drum material used in commercial applications. This emphasizes the composite suitability for usage in a variety of automobile components.

Microstructural, physical and mechanical characterization of grinding sludge based aluminium metal matrix composite

MMCs with Controlled Non-Uniform Distribution of Submicrometre Al2O3particles in 6061 Aluminium Alloy Matrix

Synthesis and characterization of spent alumina catalyst and grinding sludge reinforced aluminium-based composite material

Development and characterization of grinding sludge-reinforced aluminum-based composite by friction stir process technique

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Investigation on Mechanical Properties of Agro and Industrial Waste Reinforcement in Aluminium 7075 Composite with Liquid Metal Stir Casting Route

Influence of Nano-CuO on Synthesis and Mechanical Behavior of Spent Alumina Catalyst and Grinding Sludge Reinforced Aluminum Based Composite

Microstructural and wear properties of iron slag reinforced aluminum alloy (LM30) based composite prepared through a stir casting method

Experimental tribological and mechanical behavior of aluminium alloy 6061 composites incorporated ceramic particulates using Taguchi analysis

Enhancement of mechanical properties and machinability of aluminium composites by cupola slag reinforcementsVerbesserung der mechanischen Eigenschaften und Bearbeitbarkeit von Aluminiumverbundwerkstoffen durch Kupolofenschlackenverstärkungen

Experimental Investigation on Metal Matrix Nanocomposite: Aluminium Alloy 6061 and 7075 with SiC and Fly Ash

Fabrication and Characterization of Aluminum (Al-6061) Matrix Composite Reinforced with Waste Glass for Engineering Applications

Effect of nanostructured Al on microstructure, microhardness and sliding wear behavior of Al–xGnP composites by powder metallurgy (PM) route

Investigation on Mechanical Behavior of Al6061- Coconut Shell Ash- Granite Dust Reinforced Hybrid Metal Matrix Composites Manufactured using Stir Casting Technique

Synthesis of novel aluminium metal matrix composite using industrial metallic waste: Impact on wear and corrosion behaviour

Performance analysis and mechanical behavior of aluminum metal matrix composite

Effect of Nanoaluminium Nitride Ceramic Particles on Microstructure, Mechanical Wear, and Machining Behavior of Al-Si-Mg Alloy Matrix Composites Produced by Bottom Pouring Type Stir Casting Route

Investigate the mechanical properties of Aluminium Metal Matrix Composite

Analysis and Experimental Investigation of A356 Aluminium Alloy Hybrid Composites Reinforced with Gr-FE3O4-B4C Nanoparticles Synthesised by Selective Laser Melting (SLM)

Green metal matrix composites: a multi-faceted study on Al alloy composites with egg shell powder and silicon carbide as reinforcements

Microstructural Characterization, Mechanical And Wear Behaviour Of Al2024-B4C Composites For Aerospace Applications