Abstract:Ultra-high nickel single-crystal cathode materials have become the most promising for lithium-ion batteries. However, the preparation of ultra-high nickel single-crystal precursors by a continuous coprecipitation method has the disadvantages of large particle size, wide distribution, poor morphology. The extent of the inhomogeneous reactions can be more severe in single-crystal cathodes with larger particle size. Herein, the coprecipitation method with a solid concentrator was adopted, and citrate sodium was used as a complexing agent to improve the physical properties of precursors and electrochemical performance of single-crystal cathode materials. By analyzing the morphology and agglomeration mechanism of the precursor nucleuses under different pH values, it was found that hexagonal nanosheets grew along the 101 direction, and the primary particles showed thicker at pH of 11.4. The hexagonal nanosheets grew along the 001 direction, and the primary particles showed finer at pH of 12.2. The morphology and particle size uniformity of the secondary particles formed by agglomeration at these two pH values showed poor. However, hexagonal nanosheets grew synergistically along the 001 and 101 directions at pH of 11.8, so the primary particles with uniform particle size gradually agglomerated, and then the secondary particles with ultra-small particle size and uniform distribution obtained. Compared to materials prepared by the traditional continuous coprecipitation method, the precursor displays a smaller particle size(D50 = 1.8 µm), higher sphericity, uniformity and denser internal structure. In order to evaluate the performance of Ni0.94Co0.04Mn0.02(OH)2 with ultra-small particle size, the sintering conditions of LiNi0.94Co0.04Mn0.02O2 need to be explored. It was found that the LiNi0.94Co0.04Mn0.02O2 cathode material prepared at 790 °C exhibited higher discharge capacity, cycle and rate performance, compared to materials prepared at 760 °C and 820 °C. We further utilized TEM, EPMA, and XPS to test the internal structure and valence state of LiNi0.94Co0.04Mn0.02O2 cathode material. The results show that the LiNi0.94Co0.04Mn0.02O2 calcined at 790 °C has a good single crystal structure. The LiNi0.94Co0.04Mn0.02O2 cathode materials inherited the structure and particle size of Ni0.94Co0.04Mn0.02(OH)2 precursors, and displayed discharge capacity of 194.7 mAh/g and capacity retention rate of 89.8 % after 100 cycles at 1 C. The microstructure and phase transition of the as-prepared cathode material are well-maintained after long-term cycling, without obvious inter-crystalline micro-crack. The results indicate that its electrochemical performance is better than that of cathode materials with precursors prepared by a continuous coprecipitation method. This work provides new insights for the preparation of small-particle-size precursor and single-crystal cathode materials.

Synthesis of submicron-sized LiNi0.5Co0.2Mn0.3O2 cathode particles via reverse microemulsion method: Tailoring size, interfacial properties, and enhanced electrochemical performance for lithium-ion battery

Micron-Sized Monodisperse Particle LiNi0.6Co0.2Mn0.2O2 Derived by Oxalate Solvothermal Process Combined with Calcination as Cathode Material for Lithium-Ion Batteries

Grain size regulation for balancing cycle performance and rate capability of LiNi0.9Co0.055Mn0.045O2 single crystal nickel-rich cathode materials

Synthesis of single-crystal LiNi0.8Co0.1Mn0.1O2 materials for Li-ion batteries by microfluidic technology

A simple one-step molten salt method for synthesis of micron-sized single primary particle LiNi0.8Co0.1Mn0.1O2 cathode material for lithium-ion batteries

Synthesis of Monodisperse and Discrete Ultra-High Nickel LiNi0.97Co0.02Mn0.01O2 Octahedral Single Crystals via Single Crystal Intermediates for Li-Ion Batteries

Electrochemical performance studies of Li-rich cathode materials with different primary particle sizes

Synthesis and Evaluation of Microspherical Li1.2Mn0.54Co0.13Ni0.13O2 Through Carbon Dioxides-assisted Co-precipitation Method for Lithium-ion Battery

Spray-assisted synthesis of ant-cave-structured Ni-rich cathode microspheres with Li-reactive coating layer for high-performance Li-ion batteries

Systematic Optimization of Battery Materials: Key Parameter Optimization for the Scalable Synthesis of Uniform, High-Energy, and High Stability LiNi 0.6 Mn 0.2 Co 0.2 O 2 Cathode Material for Lithium-Ion Batteries

Application of precursor with ultra-small particle size and uniform particle distribution for ultra-high nickel single-crystal cathode materials by coprecipitation method

Synthetic Optimization and Electrochemical Properties of LiNi_(0.5)Mn_(0.5)O_2 Cathode Materials for Lithium-ion Batteries

Hydrothermal Synthesis and Electrochemical Performance of Micro-spherical LiNi1/3Co1/3Mn1/3O2 Cathode Material

Effect of Subtle Changes in Ni2+/Ni3+ and Particle Surface Area in LiNi0.5Mn0.5-xCoxO2 (x = 0.1 - 0.3) Cathode Materials for Lithium-Ion Batteries

Size controllable single-crystalline Ni-rich cathodes for high-energy lithium-ion batteries

Synthesis of Hollow Microspheres LiNi0.5Mn1.5O4 Coated With Al2O3 and Characterization of the Electrochemical Capabilities

Synthesis and Electrochemical Properties of LiNi0. 5Co0. 5O2 Cathode Material for Lithium Ion Battery

LiMn2O4 Nanorods, Nanothorn Microspheres, and Hollow Nanospheres as Enhanced Cathode Materials of Lithium Ion Battery

Tailoring electrolyte to enable high-rate and super-stable Ni-rich NCM cathode materials for Li-ion batteries

Lini0.7co0.15mn0.15o2 Microspheres As High-Performance Cathode Materials for Lithium-Ion Batteries

An Efficient Synthetic Method To Prepare High-Performance Ni-Rich Lini0.8co0.1mn0.1o2 For Lithium-Ion Batteries