Assessment of In-Service Transformers Filled with Synthetic Ester at 33 kV and Below-Part 2

Rafat Aljarrah,Muhammad Daghrah,Ayham Bakeer

DOI: https://doi.org/10.1109/mei.2024.10381676

IF: 2.939

2024-02-02

IEEE Electrical Insulation Magazine

Abstract:The assessment presented indicates ongoing operation of transformers filled with synthetic ester after many years in service.

engineering, electrical & electronic

What problem does this paper attempt to address?

Investigation of Cellulose Insulation Ageing in Transformers Retrofilled with Ester Fluids at Different Service Years

Anupam Dixit,Hui Ma,Chandima Ekanayake,Muhammad Daghrah,Tapan Kumar Saha

DOI: https://doi.org/10.1109/tdei.2024.3373557

IF: 2.509

2024-01-01

IEEE Transactions on Dielectrics and Electrical Insulation

Abstract:Retro-filling transformers with ester fluids have been increasingly practiced. Transformers may be retrofilled at different service years. In this paper, the ageing behaviour of the cellulose insulation of transformers retrofilled at different service years (with different conditions of paper insulation) are studied. Since the temperature may rise after the retrofill due to the high viscosity of the ester liquids, a temperature increase of 10 °C and 20 °C in cellulose-liquid insulation systems after retrofill is considered. The degree of polymerization (DP) of the cellulose insulation and the moisture in both cellulose and liquid insulation are measured before and after retrofilling. The measurements are used for modelling the remaining useful life of the cellulose-liquid insulation system. The process of insulation systems reaching the impregnation equilibrium after retrofilling is investigated through the fire and flash point measurements of the liquid insulation and frequency domain spectroscopy (FDS) measurements of the cellulose-liquid insulation system.

engineering, electrical & electronic,physics, applied
Improvement of Some Chemical and Electrical Properties of Aged Transformer Oil using Eco-Friendly Fillers

DOI: https://doi.org/10.21608/aujes.2020.127569

2020-12-05

Aswan University Journal of Environmental Studies

Abstract:Transformers are the main component in power generation industries and play a vital part in supplying electricity all over the world. Two main insulators are used in transformers, solid insulator or cellulosic paper and liquid insulator known as insulating oil or transformer oil. Transformer oil has the function of insulation and cooling as basic function also, it is used in suppressing electrical charge and preserving inner component of transformer against corrosion. During service oil deterioration take place under the impact of thermal and electrical stresses. Chemical composition of oil changes with formation of oxidation products and oil characteristics is no longer existing, hence, Transformer oil is monitored in terms of chemical, physical and electrical properties while dissolved gases is carried out by gas chromatography. After years in service, aging of transformer oil with formation of oxidation products is mandatory, looking for solutions able to regenerate oil and remove undesired products without being harmful to original composition of oil chains is required. Treatment of aged oil get attention recently with reclaiming by variety of chemical techniques and different materials for improvement of its properties and maintain these oils in operation for next years. This study represents reclaiming procedure by means of three eco-friendly inorganic fillers: Activated Bentonite (AB), Activated Carbon (AC) and Silica Fume (SF) which used in form of mixture fillers in the sequence of (AB+AC), (AB+SF) and (SF+AC). The main scope is reclaiming aged transformer oil and using mixture technique for efficacy of two fillers despite one. Three properties acidity as a chemical property, dissipation factor and breakdown voltage as electrical properties are tested for the series of mixtures, improvement was achieved providing an environmental reclaiming procedure. Best result in acidity is attributed to mixture 1:5 (AB+SF) with 0.072 mg KOH/g oil and enhancement percentage of -30.8% while improvement in dissipation factor showed result of 0.039 and an enhancement of 61% for mixture 1:7 SF+AC. Breakdown voltage showed improvement of 122.9% of 78 KV/2.5 mm for mixtures 3:1, 5:1 and 7:1 (AB+SF).
Automated dry-type transformer aging evaluation: A simulation study

Ilyas Soltanbayev,Radkhan Sarmukhanov,Sanzhar Kazymov,Talgat Otelgen,Mehdi Bagheri

DOI: https://doi.org/10.1109/sibcon.2017.7998478

2017-06-01

Abstract:Transformer operation conditions are quite crucial for industry as they have significant influence on transformer remained lifetime. This influence becomes even more significant once transformer operates at high ambient temperature. Hence, development of an intelligent system that able to monitor the effect of environmental conditions on remained lifetime together with aging rate, and provide information in real time is substantial. This study is focused on an online system forecasting transformer aging rate and remained life. To evaluate the proposed model, simulation results are compared to calculations proposed by IEC standards. Moreover, system's behavior under real life conditions is analyzed and results suggesting possible industry enhancements are provided.
Modified Dissolved Gas Analysis Scoring Approach for Transformer Health Evaluation Considering Delta and Rate Values of Dissolved Gases in Mineral Oil

Mehmet Aytac Cinar

DOI: https://doi.org/10.3390/en17164161

IF: 3.2

2024-08-23

Energies

Abstract:Transformers are among the most important components in the energy grid due to their missions and high costs. The challenging operating conditions deteriorate their components and shorten the life of the transformers. The health index approach is a critical and effective method for monitoring transformers in the operating environment, early diagnosis of possible malfunctions, and evaluation of their general condition. DGA, OQA, and PIF parameters, which represent the condition of the insulation materials, which mainly determine the life of transformers, constitute the basic inputs of the health index approach. In this study, a new method was proposed to determine the DGAF score based on the dissolved gases in mineral oil. With this method, in addition to the delta and rate values of the gases, the past DGA results of the transformer were also considered in determining the DGAF. In this way, faults experienced during operation are included in the health index calculation. The proposed method was tested using 36 DGA results obtained over a period of approximately 10 years from a transformer operating in the grid. The obtained results are presented in comparison with the traditional DGAF scoring method.

energy & fuels
Influence of Nanoparticles on the Degradation Processes of Ester-Based Transformer Insulation Systems

Daniel Pérez-Rosa,Belén García,Juan Carlos Burgos

DOI: https://doi.org/10.3390/en15041520

IF: 3.2

2022-02-18

Energies

Abstract:The use of nanofluids as dielectric liquids for transformer insulation has been widely investigated during the last decade. A number of authors have performed extensive studies on liquids produced from different types of nanoparticles and base fluids, providing evidence of their good dielectric properties. Nevertheless, nanodielectric fluids are still at the research stage, and they are far from being a solution that can be applied to real transformers. One of the aspects that might be clarified is their compatibility with the rest of the materials present in the transformer and their behavior throughout the life of the equipment. This paper studies the aging process of cellulose impregnated with an ester-based nanofluid and compares it with the process that takes place when the impregnation liquid is a natural ester. Accelerated aging experiments were performed, and physical and chemical characterization of the process with several analytical techniques was carried out. The mechanical degradation of the cellulose was studied in terms of tensile strength, and the evolution of moisture in the paper and oil was monitored throughout the aging process. The study was completed with FTIR and XPS tests aimed at studying the chemical changes of the materials during the aging process. The experimental results suggest that the degradation rate of the cellulose is not significantly affected by the presence of nanoparticles. However, the XPS study revealed that the chemical reactions involved in the degradation processes of both types of insulation might differ. Several mechanisms are proposed in this work.

energy & fuels
Maintenance Enhancement of the Performance of Aged Voltage Transformers Using Nanoparticles

Saad A. Mohamed Abdelwahab,Ahmed A. Salem,Mohammed Shaban,Sherif S. M. Ghoneim

DOI: https://doi.org/10.1109/tdei.2024.3365670

IF: 2.509

2024-01-01

IEEE Transactions on Dielectrics and Electrical Insulation

Abstract:The current work proposes a new VT maintenance approach for restoring the oil’s insulation properties depending on the nanoparticles’ advantages. For the first time, a real-aged VT was used for the experimentation. Different experimental tests were performed and assessed on VT to ensure the effectiveness of the proposed technique, such as breakdown voltage (BDV), dissipation factor (DF), and insulation resistance (IR) tests. The experimental tests of VT were carried out before and after the treatment and compared with the new oil to prove the feasibility and robustness of the proposed technique. The experimental tests of VT were examined according to IEC standards. Based on the results, a significant improvement in the oil’s BDV and the insulation performance of the VT was conducted, indicating the substantial impact of nanoparticles for enhancing the maintenance of aged VT. The results indicated a significant improvement in the BDV of the oil and the insulation performance of the VT. Furthermore, a statistical analysis tool is used to assess and evaluate the accuracy of the experimental test. In addition, the K Nearest Neighbors (KNN) classifier was conducted to diagnose and predict the state of the VT, the fine KNN developed 100 % classification accuracy compared to 96.7 % accuracy for the coarse KNN classifier. The recorded experimental measurements and the numerical results emphasize that the proposed method provides superior features.

engineering, electrical & electronic,physics, applied
Research Progress of the Dissolved Gas Analysis in Synthetic Ester Insulating Oil under Electrical Faults

Feipeng Wang,Xingyu Chen,Chao Song,Liangxuan Ouyang

DOI: https://doi.org/10.1109/ICHVE53725.2022.9961566

2022-09-25

Abstract:Transformers will be subjected to electrical, thermal, and mechanical stresses during operation, causing decomposition of the insulation materials and consequently generating gas in the oil. Early transformer faults including electrical faults can be detected in time through DGA (Dissolved Gas-in-oil Analysis) which can reflect the state information of insulating oil transformers. Recently, the application of synthetic insulating oil in large power transformers could increase due to excellent fire resistance, environmental protection, strong oxidation stability, etc. Due to the differences in molecular structure between synthetic ester insulating oils and mineral insulating oils as well as natural ester insulating oils, there are differences in the characteristics of dissolved gas in the oil produced under electrical faults, resulting in different limits of dissolved gas in the oil under normal and fault conditions. In order to ensure the safe and reliable operation of synthetic ester insulating transformers, this paper reviews the analysis on faulty gas production of synthetic ester insulating oil and summaries the commonly used diagnostic methods for synthetic insulating oil under electrical faults.

Environmental Science,Engineering
Assessment of Thermophysical Performance of Ester-Based Nanofluids for Enhanced Insulation Cooling in Transformers

Suhaib Ahmad Khan,Mohd Tariq,Asfar Ali Khan,Basem Alamri,Lucian Mihet-Popa

DOI: https://doi.org/10.3390/electronics11030376

IF: 2.9

2022-01-26

Electronics

Abstract:Nanotechnology provides an effective way to upgrade the thermophysical characteristics of dielectric oils and creates optimal transformer design. The properties of insulation materials have a significant effect on the optimal transformer design. Ester-based nanofluids (NF) are introduced as an energy-efficient alternative to conventional mineral oils, prepared by dispersing nanoparticles in the base oil. This study presents the effect of nanoparticles on the thermophysical properties of pure natural ester (NE) and synthetic ester (SE) oils with temperature varied from ambient temperature up to 80 °C. A range of concentrations of graphene oxide (GO) and TiO2 nanoparticles were used in the study to upgrade the thermophysical properties of ester-based oils. The experiments for thermal conductivity and viscosity were performed using a TC-4 apparatus that follows Debby’s concept and a redwood viscometer apparatus that follows the ASTM-D445 experimental standard, respectively. The experimental results show that nanoparticles have a positive effect on the thermal conductivity and viscosity of oils which reduces with an increase in temperature.

engineering, electrical & electronic,computer science, information systems,physics, applied
Aging Diagnosis of Solid Insulation for Large Oil-Immersed Power Transformers

M Dong,Y Shang,WB Zhao,Z Yan,Z Zheng

DOI: https://doi.org/10.1109/ceidp.2002.1048819

2002-01-01

Abstract:Furfural analysis has been proved a useful tool for the aging diagnosis of solid insulation in large oil-immersed power transformers. Up-to-now, diagnostic criteria for operating transformers are in urgent need. In the investigation, quite a lot of data have been collected, such as the furfural concentrations, service durations, water contents, etc. To reveal the relationship between furfural contents in oil and the aging condition of solid insulation, statistic analyses are carried out. Then, the factors affecting the aging process such as service duration is studied. Therefore, the statistic distribution of furfural concentration in oil is worked out. According to the theoretical distribution, several warning levels of furfaral in oil could be calculated, which are more reasonable than that the regulation had recommended. An example of practical application shows it is effective and easy to apply for operating transformers.
Field Diagnosis on Transformers for Wind Turbine Applications

A. Thiede,U. Kaltenborn,M. Hensel

DOI: https://doi.org/10.1109/gtdasia.2019.8715937

2019-03-01

Abstract:Distribution transformers used in wind turbine applications are exposed to additional stress caused by permanent mechanical vibrations, strong load cycling and harsh climatic conditions. These influences can cause an accelerated ageing of the insulation system and shortening of the life expectancy of these essential components of wind power stations. To avoid spontaneous failure of the transformer, regular on site diagnosis contributes to an increased reliability of the whole power system by early detection of the degradation of the insulation system. An induced voltage test with partial discharge measurement is the most significant and productive method for the assessment of the dielectric condition. The most efficient way with respect to availability and logistics is to perform the induced voltage test on-site. Because of the very limited space inside the wind power systems, specialized test equipment was developed for the regular on-site inspection. This compact test voltage source is based on a small IGBT inverter with filter and step-up transformer. It comprises a state of the art control computer to enable a closed loop control of the test voltage. The test voltage source is divided into three small transport units (boxes) and can be used directly in the nacelle. First field tests in 2017 proved the suitability of the compact test voltage source to perform induced voltage tests with accompanying partial discharge measurement. Such field tests were executed continuously throughout the last years and it could be proven that the test system could be integrated into the different service regimes. The test system is suitable for the on-site diagnosis of any kind of cast-resin and distribution transformer too.
Causes of transformer failures and diagnostic methods – A review

Christina Aj,M.A. Salam,Q.M. Rahman,Fushuan Wen,S.P. Ang,William Voon

DOI: https://doi.org/10.1016/j.rser.2017.05.165

2018-01-01

Abstract:This paper presents a review on the sources of failures of transformer in the substation. Different investigations and test analyses have been conducted to identify the root causes of failure of the transformer in the power system, and to identify the preventive measures to avoid these breakdowns. The review work has been presented with the focus on bushing-failure, which has been identified as one of the major causes of transformer breakdown in different reported studies. In determining the lifespan of the insulation of the high voltage bushing, along with different factors, moisture effect has also been considered in presenting the degradation analysis. On-line measurement has been preferred over off-line measurements due to its benefits measuring the reliability and uninterrupted functioning of the future generation, transmission and distribution systems. Post fire-outbreak, external inspection of the damaged bushing along with analytical results, obtained with the aid of Scanning Electron Microscope (SEM) and Energy Dispersive X-ray Spectroscopy (EDS) analysis, have also been included in this study. In the analysis, electric field and equipotential lines with different oil levels have been simulated using COMSOL Multiphysics software.
Innovative Transformer Life Assessment Considering Moisture and Oil Circulation

Zhengping Liang,Yan Fang,Hao Cheng,Yongbin Sun,Bo Li,Kai Li,Wenxuan Zhao,Zhongxu Sun,Yiyi Zhang

DOI: https://doi.org/10.3390/en17020429

IF: 3.2

2024-01-17

Energies

Abstract:Power transformers are one of the most expensive and important equipment in the power system. Significant differences exist in the insulation lifespan of transformers that have been in operation for more than 20 years, and using identical maintenance or scrapping methods may result in significant economic losses. However, most existing transformer life assessment methods only consider the impact of moisture content on the life decay rate without considering the impact of oil circulation cooling modes, which leads to some evaluation errors. In this study, we established a new transformer life assessment method that considers the influence of moisture content and oil circulation cooling modes, which is more accurate than most life assessment methods. Then, the proposed life evaluation method was validated on the on-site transformers, demonstrating its accuracy and effectiveness. The novelty of this study is that it establishes a new on-site transformer life assessment method that considers the comprehensive effect of moisture content and oil circulation cooling mode, which helps to evaluate the remaining lifespan of power transformers more accurately and thus extends the transformer lifespan systematically.

energy & fuels
Power transformer faults diagnosis using undestructive methods (Roger and IEC) and artificial neural network for dissolved gas analysis applied on the functional transformer in the Algerian north-eastern: a comparative study

Bouchaoui Lahcene,Kamel Eddine Hemsas,Hacene Mellah,saad eddine benlahneche

DOI: https://doi.org/10.20998/2074-272X.2021.4.01

2021-08-02

Abstract:Nowadays, power transformer aging and failures are viewed with great attention in power transmission industry. Dissolved gas analysis (DGA) is classified among the biggest widely used methods used within the context of asset management policy to detect the incipient faults in their earlier stage in power transformers. Up to now, several procedures have been employed for the lecture of DGA results. Among these useful means, we find Key Gases, Rogers Ratios, IEC Ratios, the historical technique less used today Doernenburg Ratios, the two types of Duval Pentagons methods, several versions of the Duval Triangles method and Logarithmic Nomograph. Problem. DGA data extracted from different units in service served to verify the ability and reliability of these methods in assessing the state of health of the power transformer. Aim. An improving the quality of diagnostics of electrical power transformer by artificial neural network tools based on two conventional methods in the case of a functional power transformer at Sétif province in East North of Algeria. Methodology. Design an inelegant tool for power transformer diagnosis using neural networks based on traditional methods IEC and Rogers, which allows to early detection faults, to increase the reliability, of the entire electrical energy system from transport to consumers and improve a continuity and quality of service. Results. The solution of the problem was carried out by using feed-forward back-propagation neural networks implemented in MATLAB-Simulink environment. Four real power transformers working under different environment and climate conditions such as: desert, humid, cold were taken into account. The practical results of the diagnosis of these power transformers by the DGA are presented. Practical value.....

Signal Processing,Machine Learning,Systems and Control
A Comparative Analysis of Partial Discharge in 13 Combined Insulation Structures of 11 Materials Used in Cast-Resin Dry-Type Transformers

Muzaffer Erdogan,Mehmet Kubilay Eker

DOI: https://doi.org/10.1109/tdei.2022.3205285

IF: 2.509

2022-12-28

IEEE Transactions on Dielectrics and Electrical Insulation

Abstract:Partial discharge (PD) in cast-resin dry-type transformers (CRDTs) is an important issue that needs to be overcome. In this study, PD in insulation materials used in CRDT windings is investigated. Four types of samples are prepared using 11 different types of materials, including epoxy resin, three-ply glued polyester insulation, prepreg insulation, glass fiber mesh, polyester adhesive tape, polyester film, polyimide film, rectangular conductors with polyester insulation, round conductors with polyester insulation, round conductors with enamel insulation, and foil conductors without insulation, and subjected to PD measurements. The samples are placed into a mold for resin casting that is similar to those used to fabricate large cast-resin windings, and the material behavior is tested. PD measurements are carried out in the high-voltage laboratory of the BEST Transformer Company. The measured data are used as inputs to models of the samples that are simulated using finite element analysis software to determine the PD inception electric field. The PD patterns of the samples are compared with well-known PD patterns in the literature. Finally, a comparative analysis of the materials is performed, and strong and weak materials against PD are identified. The results of this study show that laminated insulation materials or fiberglass meshes, both with epoxy resin, which have PD inception at a mean value of 3.4 kV/mm of electric field intensity, are more susceptible to PD than the other insulation materials investigated. In contrast, insulated conductors or nonlaminated polyester or polyimide films, all with epoxy resin, which have PD inception above a mean value of 5.3 kV/mm of electric field intensity, are robust to PD.
Evolution of graphical methods for the identification of insulation faults in oil-immersed power transformers: A review

Sergio Bustamante,Mario Manana,Alberto Arroyo,Alberto Laso,Raquel Martinez

DOI: https://doi.org/10.1016/j.rser.2024.114473

IF: 16.799

2024-05-08

Renewable and Sustainable Energy Reviews

Abstract:The power transformer is one of the most important and critical assets involved in the grid and, at the same time, one of the most expensive. Several transformer condition parameters allow to assess the degradation of assets. These help in the decision-making process on the operation, repair, refurbishment, or replacement of transformers. Dissolved gas analysis (DGA) is one of the most commonly used methods to manage maintenance and establish the health index of power transformers, as well as to identify the type of fault. This paper examines and explores the studies related to graphical methods for the identification of faults in power transformers that had been developed over the last almost 50 years. The main types of faults and the sub-types presented in the analysed studies are compiled in this paper. The main differences between the methods in terms of their graphical representation, number of gases used, type of data used from the DGA results, and number of faults and sub-faults identifiable in each of them, are also presented. The application of the reviewed methods was carried out using two real DGA results.

energy & fuels,green & sustainable science & technology
Transformer Health Monitoring Using Dissolved Gas Analysis

Cody Walker,Ahmad Al Rashdan,Vivek Agarwal

DOI: https://doi.org/10.36001/ijphm.2022.v13i2.3141

2022-07-12

International Journal of Prognostics and Health Management

Abstract:As integral components of any power plant, transformers sup-ply the generated electricity to the grid. However, the trans-former’s cellulose-based paper insulation and the mineral oilin which it is immersed break down over time under stan-dard operating conditions—or more rapidly due to potentialfaults within the system. This technical brief exhibits a col-lection of diagnostic and prognostic techniques that utilitiescan adopted in lieu of labor-intense periodic preventive main-tenance routines. Furthermore, prognostic models have beenincorporated using the latest version of the Institute of Elec-trical and Electronics Engineers (IEEE) standard (IEEE StdC57.104TM-2019) for dissolved gas analysis (DGA), thusexpanding it to include estimation of the time to maintenance.Overall, four different methodologies are explained, each ofwhich aid in determining a transformer’s state of health. Thesemethodologies include the Chendong model, the IEEE C57.91-2011 thermal life consumption model, a diagnostic model forDGA, and a prognostic model for DGA that uses an autore-gressive integrated moving average (ARIMA) model. An ad-ditional improvement for estimating missing system parame-ters from monitoring data (i.e., a tool for parameter estimationutilizing Powell’s method) is presented, enabling the IEEEthermal life consumption model to benefit not only the col-laborating power plant, but also the power industry at large.
Analysis of the Influence of Insulation Moisture during Long-Term Exploitation of Transformers on Their Reliability as Determined by Alternating Current Electrical Parameters

Pawel Zukowski,Konrad Kierczynski,Przemyslaw Rogalski,Vitalii Bondariev,Marek Zenker,Rafal Pajak,Marek Szrot,Pawel Molenda,Tomasz N. Koltunowicz

DOI: https://doi.org/10.3390/en17081952

IF: 3.2

2024-04-20

Energies

Abstract:This paper presents the results of the study of the direct current (DC) and alternating current (AC) electrical properties of an electrical pressboard–bio-insulating oil–water composite in a wide range of water content and temperatures used in electric power transformers. These parameters allow the level of insulation reliability to be determined after many years of operation of power transformers. To analyse the experimental results, a model of the DC and AC conductivities of nanocomposites based on the quantum-mechanical phenomenon of electron tunnelling was used. It was found that in a low-frequency region, the conductivities of AC and DC and their activation energy are equal. The relaxation times of AC conductivity and permittivity are also equal. It was found that the dependence of the DC conductivity on the distance between water molecules is an exponential function. On the basis of the model of conductivity by electron tunnelling between potential wells, the average number of water molecules in a nanodroplet, located in a composite of electrical pressboard–bio-insulating oil–moisture was determined to be (126 ± 20). It was found that the measured dependencies of DC and AC conductivity, permeability and dielectric relaxation times are consistent with the results of computer simulations performed on the basis of the model. This study showed that the composite of pressboard impregnated with bio-oil spontaneously transforms through water absorption into a pressboard–bio-oil–water nanocomposite. These will serve as the basis for the application of actual conductivity and dielectric relaxation mechanisms to improve the accuracy of moisture estimation in the solid component of power transformer insulation carried out on the basis of measurements of DC and AC properties. This will improve the operational safety of the transformers, minimise the occurrence of transformer failure and the associated environmental pollution.

energy & fuels
Review of condition assessment of power transformers in service

M. Wang,A.J. Vandermaar,K.D. Srivastava

DOI: https://doi.org/10.1109/mei.2002.1161455

IF: 2.939

2002-11-01

IEEE Electrical Insulation Magazine

Abstract:As transformers age, their internal condition degrades, which increases the risk of failure. To prevent these failures and to maintain transformers in good operating condition is a very important issue for utilities. Traditionally, routine preventative maintenance programs combined with regular testing were used. The change to condition-based maintenance has resulted in the reduction, or even elimination, of routine time-based maintenance. Instead of doing maintenance at a regular interval, maintenance is only carried out if the condition of the equipment requires it. Hence, there is an increasing need for better nonintrusive diagnostic and monitoring tools to assess the internal condition of the transformers. If there is a problem, the transformer can then be repaired or replaced before it fails. An extensive review is given of diagnostic and monitoring tests, and equipment available that assess the condition of power transformers and provide an early warning of potential failure.

engineering, electrical & electronic
Synthetic Furfural Analysis For Transformer Ageing

Ming Dong,Guanjun Zhang,Zhang Yan

DOI: https://doi.org/10.1109/ceidp.2004.1364234

2004-01-01

Abstract:Measuring the furfural content with the High Performance Liquid Chromatograph HPLC is an effective method, as it will be helpful to trace the aging of oil-immersed transformers. But the measured generally affected by many factors, such as load, temperature, etc., and it often fluctuates a lot after refining the oil of transformer. In this paper, recent-year laboratory researches and field experiences on furfural analysis in China are introduced. And the depolymerization rate of cellulosic paper is studied in laboratory, as well as the accumulation of furanic compounds in the same transformer. According to the laboratory research, the aging status of cellulosic insulating paper may be determined. Furthermore, combining the measurement of CO, CO2 with Dissolved Gas Analysis DGA and the furfural content is developed, so the synthetic ageing diagnosis based on those measured data was improved also. Besides, the laboratory results are revised for field utilization, taking into account of the differences existing between the laboratory condition and the fields. Rather good agreement has been verified when applying those improved results to many in-service transformers on site.
Accurate Assessment of Moisture Content and Degree of Polymerization in Power Transformers via Dielectric Response Sensing

Anantawat Kunakorn,Sarawuth Pramualsingha,Peerawut Yutthagowith,Phethai Nimsanong,Supat Kittiratsatcha

DOI: https://doi.org/10.3390/s23198236

2023-10-03

Abstract:Power transformers are essential apparatuses used to transfer electrical energy from one voltage-level circuit to another. For reliable systems, preventive maintenance of the transformers is required to ensure good services of all mechanical, electrical, and insulation parts. Oil-immersed paper is most often used for transformer insulation. To ensure such good insulation performance and for assessing insulation conditions, advanced transformer sensing, monitoring, and effective assessment techniques are required. This paper introduces an effective technique for assessing the insulation conditions in power transformers, which are crucial for ensuring reliable energy transfer. The method utilizes advanced transformer sensing and monitoring, focusing on oil-immersed paper insulation commonly used in transformers. The technique employs dielectric response sensing, obtained from frequency-domain spectroscopy tests, to estimate degrees of polymerization (DP) and percentages of moisture content (PMCs) in the oil-immersed paper insulation. These parameters are well-known indicators of insulation performance. The approach is based on the weighted k-nearest neighbor regression, using a database of dielectric loss factors at low frequency and oil conductivities. To overcome limited data availability, linear interpolation and extrapolation techniques are applied to enlarge the database. Experimental verification and comparison with a previously developed method demonstrate the proposed technique's superiority in accuracy and complexity. The maximum deviations of DP and PMC in the validation cases are 6.2% and 18.7%, respectively. In addition, to evaluate the validity of our proposed method in the case of a real power transformer, a comparative analysis of the DP and PMC values determined by the proposed method with those obtained through a previously developed and complicated approach was performed. The predicted results indicate that the DP and PMC values of the oil-immersed insulation fall within the ranges of 800 to 1000 and 1.5 to 2.0, respectively, which agree with the results determined by the complicated approach and closely align with real conditions. By offering a reliable and advanced means of assessing insulation conditions, this technique contributes to the preventive maintenance and overall efficiency of power transformers.

Assessment of In-Service Transformers Filled with Synthetic Ester at 33 kV and Below-Part 2

Investigation of Cellulose Insulation Ageing in Transformers Retrofilled with Ester Fluids at Different Service Years

Improvement of Some Chemical and Electrical Properties of Aged Transformer Oil using Eco-Friendly Fillers

Automated dry-type transformer aging evaluation: A simulation study

Modified Dissolved Gas Analysis Scoring Approach for Transformer Health Evaluation Considering Delta and Rate Values of Dissolved Gases in Mineral Oil

Influence of Nanoparticles on the Degradation Processes of Ester-Based Transformer Insulation Systems

Maintenance Enhancement of the Performance of Aged Voltage Transformers Using Nanoparticles

Research Progress of the Dissolved Gas Analysis in Synthetic Ester Insulating Oil under Electrical Faults

Assessment of Thermophysical Performance of Ester-Based Nanofluids for Enhanced Insulation Cooling in Transformers

Aging Diagnosis of Solid Insulation for Large Oil-Immersed Power Transformers

Field Diagnosis on Transformers for Wind Turbine Applications

Causes of transformer failures and diagnostic methods – A review

Innovative Transformer Life Assessment Considering Moisture and Oil Circulation

Power transformer faults diagnosis using undestructive methods (Roger and IEC) and artificial neural network for dissolved gas analysis applied on the functional transformer in the Algerian north-eastern: a comparative study

A Comparative Analysis of Partial Discharge in 13 Combined Insulation Structures of 11 Materials Used in Cast-Resin Dry-Type Transformers

Evolution of graphical methods for the identification of insulation faults in oil-immersed power transformers: A review

Transformer Health Monitoring Using Dissolved Gas Analysis

Analysis of the Influence of Insulation Moisture during Long-Term Exploitation of Transformers on Their Reliability as Determined by Alternating Current Electrical Parameters

Review of condition assessment of power transformers in service

Synthetic Furfural Analysis For Transformer Ageing

Accurate Assessment of Moisture Content and Degree of Polymerization in Power Transformers via Dielectric Response Sensing