Abstract:Objective: to evaluate microshear bond strength of CAD/CAM composite block and hybrid ceramic block repaired by direct resin composite restoration with and without surface treatment.Materials and Methods: Two different CAD/CAM restorative materials were tested in the present study: hybrid ceramic blocks (Vita Enamic) and resin composite blocks (Grandio). Six sections were prepared from each CAD/CAM blocks. The sections from each block type were randomly divided into three groups according to the surface treatment performed. Control group: the specimens were ground with a grinding machine. Etching gel Group: 37% phosphoric acid etching gel was applied occlusally on the surface of the section and CoJet Group. the surface of all groups were then silanized using Bis-Silane then bonding agent Futura bond DC was applied. A polyethylene micro tubes were prepared that were held in place with a tweezer on the uncured then light cured for 10 seconds Resin composite (Grandioso X-tra) was packed inside the microtubes and light cured. All specimens were prepared by the same operator at 22.0–22.5 ˚C (room temperature) and relative humidity of 50%. The specimens were further divided into two groups according to storage conditions. Half of the specimens were thermocycled in distilled water for 5000 cycles in a 5–55˚C water bath with a dwell time of 30 seconds and a transfer time of 5 seconds. The other specimens were stored in distilled water for 2 days. Microshear bond strength was performed and fractographic analysis to determine the failure mode. Statistical analysis was then performed using a commercially available software program (SPSS 19; SPSS, Chicago, IL, USA). As data were not normally distributed, significance of the difference between different groups within the same surface pretreatment was evaluated using Kruskall Wallis test. Mann Whitney U test was used for pairwise comparisons and to study the effect of surface pre-treatment. The interaction of restoration and type of pretreatment variables was evaluated using 3 ways ANOVA. The level of significance was set at P < 0.05.Results: Three ways ANOVA test revealed that each of the material type (composite/hybrid ceramic), the subgroup type group (control/etching/Cojet) and the thermocycling (Yes/No) variables resulted in a statistically significant difference (p=0.00, p=0.00, p=0.003 respectively). Interaction of the subgroup (control/etching/Cojet) variable with the thermocycling (Yes/No) variable and the material (composite/hybrid ceramic) variable showed a statistically significant difference (P=0.023, p=0.001 respectively). Moreover, interaction of thermocycling and material variable resulted in a significant difference (p=0.034). However, interaction of the 3 study variables (material, subgroup, thermocycling) was not statistically significant (p=0.165). The failure mode of the tested specimens analyzed using Scanning Electron Microscope at magnification 80X was commonly mixed type of failure (adhesive failure between resin composite restoration and CAD/CAM blocks with cohesive failure within resin composite restoration).Conclusions: Grandio composite blocks is very promising materials and their optimum long lasting repair potentiality that offers to the clinicians great chance to easily repair the defective restoration with safety. Surface treatment using Phosphoric acid or Cojet system greatly improve the bond strength between composite repair system and hybrid ceramic or composite blocks. The bond performance of repaired composite blocks was much more greater than than that of repaired hybrid ceramic. Thermocycling affect the bond durability of repaired hybrid ceramic blocks and composite blocks.Further investigations focusing on the effect of different surface treatments to yield results that lead to concrete clinical recommendations are needed to evaluate the long term durability of new CAD/CAM materials.

Effect of CAD-CAM block thickness and translucency on the polymerization of luting materials

Influence of Restoration Thickness and Resin Cement on Translucency and Color of Different Types of Monolithic Zirconia and Lithium Disilicate Ceramic

In-Office CAD/CAM Coronal Treatment With Lithium Disilicate Achieved in Efficient, Predicable Manner

Effects of CAD/CAM restorative materials and thickness on the depth of cure of various light-cured resin composite materials

A comparison of the radiopacities of CAD-CAM restoratives: Effect of thickness

Effects of Substrate and Cement Shade on the Translucency and Color of CAD/CAM Lithium-Disilicate and Zirconia Ceramic Materials

From Artisanal to CAD-CAM Blocks

The effect of cement and impression methods on the marginal and internal adaptation of the current monolithic blocks - 3D scanning evaluation

Effect of the Composition of CAD/CAM Composite Blocks on Mechanical Properties

Exploring the optical behavior and relative translucency parameter of CAD-CAM resin-based composites, polymer-infiltrated ceramic network, and feldspar porcelain

Effects of thickness and polishing treatment on the translucency and opalescence of six dental CAD-CAM monolithic restorative materials: an in vitro study

EVALUATION OF BIAXIAL FLEXURAL STRENGTH AND TRANSLUCENCY OF MULTICHROMATIC TRANSLUCENT ZIRCONIA AND LITHIUM DISILICATE CERAMICS

Physico-mechanical properties and bacterial adhesion of resin composite CAD/CAM blocks: An in-vitro study

A Comparative Evaluation of the Radiopacity of Contemporary Restorative CAD/CAM Blocks Using Digital Radiography Based on the Impact of Material Composition

Light transmittance through resin-matrix composite onlays adhered to resin-matrix cements or flowable composites

EFFECT OF DIFFERENT THICKNESSES AND TWO SHADES OF TWO CERAMIC MATERIALS ON THE DEGREE OF CONVERSION OF A LIGHT CURED RESIN CEMENT

The Influence of Thickness on Light Transmission for Pre- and Fully Crystallized Chairside CAD/CAM Lithium Disilicate Ceramics

Impact of the Microstructure of CAD/CAM Blocks on the Bonding Strength and the Bonded Interface

Influence of Ceramic Thickness on Mechanical Properties and Polymer Structure of Dual-Cured Resin Luting Agents.

Repair potentiality of CAD/CAM composite block and hybrid ceramic block by direct resin composite restoration with and without surface treatment

The effect of two preparation designs on the fracture resistance and marginal adaptation of two types of ceramic crowns using CAD/CAM technology (In vitro study)