Abstract:The present study experimentally investigates the effect of inlet distortion on the combustion process in a direct-connect test environment. A blockage by introducing physical intrusions with three heights (H = 2.5 mm, 3.2 mm, and 4 mm) was mounted at the entrance of the isolator to mimic the inlet distortion. Cases without blockage were used as a comparison. Schlieren visualization synchronized with high-speed CH* chemiluminescence imaging and pressure measurements were employed to characterize the flowfields. The results show that the blockage mounted at the entrance of the isolator could reasonably mimic distortion generated at the inlet. The combustion enhancement is achieved in all cases with blockage, and the lean blowoff limits could be widened in the combustor with blockage (H = 2.5 mm and 3.2 mm). In the cavity stabilized combustion mode and transition mode ( Φ=0.159∼ 0.689), the stronger oblique shock wave emanating from the cavity leading edge and the additional background shock wave created by the inlet distortion are the chief causes of combustion enhancement in cases with blockage. The combustion enhancement gradually recedes with the increase of blockage height. It could be speculated that the relatively concentrated impinging of the incoming shock waves induces a more remarkable combustion enhancement. In the jet-wake stabilized combustion mode ( Φ=0.848∼ 1.325), the effect of blockage height on combustion enhancement is significantly suppressed. As the equivalence ratio rises to 1.06, the regularity that the effect of blockage height on combustion enhancement is completely reversed. That is, the combustion enhancement attenuates with the decrease in blockage height. It could be inferred that in these cases, the dominance of combustion enhancement is the incoming flow velocity upstream of the reaction zone instead of the impinging sparsity of the incoming shock waves.

Effect of baffle injectors on the first-order tangential acoustic mode in a cylindrical combustor

The Effect of Swirling Injector Geometry on the Flow Dynamics of Precessing Vortex Core

Experimental study on thermoacoustic performance of radial staged combustor

Experimental Study on Self-Excited Thermoacoustic Instabilities and Intermittent Switching of Azimuthal and Longitudinal Modes in an Annular Combustor

The acoustic transfer impedance of baffled injectors in three-dimensional combustion chambers

The effect of inlet boundaries on combustion instability in a pressure-elevated combustor

Experimental Study of the Effect of Outlet Boundary on Combustion Instabilities in Premixed Swirling Flames

Experimental investigation on the effects of transverse injection distribution scheme on dual flame dynamics subjected to flow disturbances

Effects of acoustic liner on thermoacoustic instabilities in a premixed swirl combustor

The damping and locking of self-excited azimuthal modes by baffles installed in the plenum of an annular combustor

Experimental Investigations of Combustion Oscillation Modes in a Large-Aspect-ratio Dual-Mode Combustor Equipped with Multi-Strut

Experimental study on the effect of combustor configuration on the performance of dual-mode combustor

Combustion enhancement subjected to the inlet distortion in a cavity-based supersonic combustor

Suppression of Combustion Instabilities in a Premixed Swirl Combustor with Acoustic Liner

Investigation on Acoustic Properties of Thruster Chamber with Coaxial Injectors and Plenum Chamber

Effects of Baffles on Self-Triggered High Frequency Pressure Oscillations in a Thrust Chamber

Thermoacoustic Instabilities in an Annular Rotating Detonation Combustor under Off-Design Condition

Combustion instability effect on sound generation by jet diffusion flame

A 2D Low-Order Thermoacoustic Network Model of Annular Combustor with Baffles in the Plenum

Self-Excited Second-Order Azimuthal Thermoacoustic Instabilities in an Annular Combustor with Oblique-Injecting Swirling Burners

Thermoacoustic Instability Characteristics and Flame/Flow Dynamics in a Multinozzle Lean Premixed Gas Turbine Model Combustor Operated with High Carbon Number Hydrocarbon Fuels