Abstract:Dielectric elastomer (DE) is a type of electric field type electroactive polymer material that can produce greater deformation under the action of an electric field and has a faster recovery speed. It has the advantages of high energy density, large strain, low quality, and commercialization, and has become the most widely concerned and researched electroactive polymer material. In this study, copper calcium titanate (CCTO) particles with a large dielectric constant were selected as the filling phase, and a silicone rubber (PDMS) with better biocompatibility and lower elastic modulus was used as the matrix to prepare CCTO/PDMS, which is a new type of dielectric elastomer material. The structure of the dielectric elastomer is analyzed, and its mechanical properties, dielectric properties, and driving deformation are tested. Then, KH550, KH560, and KH570 modified CCTO is used in order to improve the dispersibility of CCTO in PDMS, and modified particles with the best dispersion effect are selected to prepare dielectric elastomer materials. In addition, mechanical properties, dielectric properties, and driving deformation are tested and compared with the dielectric elastomer material before modification. The results show that as the content of CCTO increases, the dielectric constant and elastic modulus of the dielectric elastomer also increase, and the dielectric loss remains basically unchanged at a frequency of 100 Hz. When the filling amount reaches 20 wt%, the dielectric constant of the CCTO/PDMS dielectric elastomer reaches 5.8 (100 Hz), an increase of 120%, while the dielectric loss at this time is only 0.0038 and the elastic modulus is only 0.54 MPa. When the filling amount is 5 wt%, the dielectric elastomer has the largest driving deformation amount, reaching 33.8%. Three silane coupling agents have been successfully grafted onto the surface of CCTO particles, and the KH560 modified CCTO has the best dispersibility in the PDMS matrix. Based on this, a modified CCTO/PDMS dielectric elastomer was prepared. The results show that the improvement of dispersibility improves the dielectric constant. Compared with the unmodified PDMS, when the filling content is 20 wt%, the dielectric constant reaches 6.5 (100 Hz). Compared with PDMS, it has increased by 150%. However, the improvement of dispersion has a greater increase in the elastic modulus, resulting in a decrease in its strain parameters compared with CCTO/PDMS dielectric elastomers, and the electromechanical conversion efficiency has not been significantly improved. When the filling amount of modified CCTO particles is 5 wt%, the dielectric elastomer has the largest driving deformation, reaching 27.4%.

Excellent dielectric and actuated strain properties in CCTOx@BT(1−x)@KH560/NR system via a tunable BaTiO3 interfacial buffer layer

A New Low Moduli Dielectric Elastomer Nano-Structured Composite with High Permittivity Exhibiting Large Actuation Strain Induced by Low Electric Field

Self‐Strengthening Dielectric Elastomer of Triblock Copolymer with Significantly Improved Electromechanical Performance under Low Voltage

Mechanisms of large actuation strain in dielectric elastomers

Improved electro‐actuation property of dielectric elastomer composites regulated by one‐dimensional CaCu3Ti4O12@TiO2 core–shell construction

Improving actuation strain and breakdown strength of dielectric elastomers using core-shell structured CNT-Al2O3

Thermoplastic Dielectric Elastomer of Triblock Copolymer with High Electromechanical Performance.

Self-healing High-performance Dielectric Elastomer Actuator with Novel Liquid-solid Interpenetrating Structure

Preparation and Characterization of CCTO/PDMS Dielectric Elastomers with High Dielectric Constant and Low Dielectric Loss

Carbon Black-Batio3/silicone Rubber Electroactive Nanocomposites with Large Strain Coefficient

End-block-curing ABA triblock copolymer towards dielectric elastomers with both high electro-mechanical performance and excellent mechanical properties

A dielectric elastomer actuator with a large actuated strain enabled by CaCu3Ti4O12/MXene/silicone dielectric composite

Enhanced Electromechanical Property of Silicone Elastomer Composites Containing TiO2@SiO2 Core-Shell Nano-Architectures

Enhanced Electromechanical Properties of Nitrile Rubber Dielectric Elastomer Composites by SrTiO3‐PPy‐PCPA Multilayer Core‐Shell Hybrids Construction

Optimizing electromechanical performance of multilayered multiwalled carbon nanotube/silicone rubber composites via filler content distribution modulation

Dielectric elastomer film with anisotropic actuation deformation on film plane

Improved the dielectric properties of thermoplastic polyurethane elastomer filled with MXene nanosheets and BaTiO3 nanofibers

Improved actuated strain of dielectric elastomer through disruption of hydrogen bonds of thermoplastic polyurethane by adding diaminonaphthalene

High performance silicate/silicone elastomer dielectric composites

Improving the electromechanical deformability of MWCNT/silicone composites via encapsulating MWCNT with polyphenols and multilayered structure regulation

Composition dependence of dielectric properties, elastic modulus, and electroactivity in (carbon black-BaTiO3)/silicone rubber nanocomposites