Abstract:MgO-Al2O3-SiO2 (MAS) glass-ceramics were prepared by traditional melting and sintering method, and the effects of MgO/Al2O3 ratios and La2O3 contents on the microstructure and physicochemical properties of MAS glass-ceramics were studied. Herein, differential scanning calorimetry (DSC), X-ray diffraction (XRD), fourier-transform infrared spectrophotometer (FTIR), Field-emission scanning electron microscopy (FESEM), density, corrosion resistance, dielectric properties and thermal expansion coefficient (CTE) were carried out to evaluate the properties of both parent glass and glass-ceramics samples. The results show that adjusting the MgO/Al2O3 ratio from 0.69 to 0.47 can increase the characteristic temperatures of transition temperature (T g ) and crystallization peak temperature (T p ) in MAS parent glass. The reduction of MgO/Al2O3 ratio could promotes the precipitation of α-cordierite phase (Mg2Al4Si5O18), and the grain size of α-cordierite phase were increased from 200 to 500 nm. When the MgO/Al2O3 ratio was 0.63, the MA-2 sample has the highest flexural strength of 127.46 MPa. Furthermore, we also investigated the influence of La2O3 addition on the structure and properties of MAS glass-ceramics by employed MA-2 sample as a reference. The results show both the T g (742–748 °C) and T p (936–943 °C) of parent glass exhibit a slightly increasing with the La2O3 content was increased from 0.0 to 2.0 wt%. The La2O3 addition show a negligible influence on the crystal phase and morphology of MAS glass-ceramics. With increasing of the La2O3 content, the MAS glass-ceramics samples have a larger density (2.58–2.76 g/cm3) and a better chemical stability, and the CTE (6.12–8.17 × 10−6/°C), ε r (5.04–6.17), and the flexural strength (127.46–150.15 MPa) also show an increased change trends. The prepared MAS glass-ceramics can be packaged with high expansion coefficient chips (such as GaAs) and is expected to become a potential candidate of dielectric materials for electronic devices, especially for high frequency applications in integrated circuits.

Lowering hot isostatic pressing temperature of ultrafine‐grained MgAl2O4 transparent ceramics by two‐step pre‐sintering

Transparent MgAl2O4 ceramics prepared by microwave sintering and hot isostatic pressing

Effect of powder dispersity on the optical properties of HIP sintered MgAl2O4 transparent ceramics

Ultra-fast high-temperature sintering of transparent MgAl2O4

Optimization of Ca additive and HIP condition in fabrication of the transparent MgAl2O4 ceramics

Magnesium aluminate spinel transparent ceramics with high optical and mechanical performance by Y3Al5O12 sintering additive

Influence of CaO on microstructure and properties of MgAl2O4 transparent ceramics

Hot isostatic pressing of transparent AlON ceramics assisted by dissolution of gas inclusions

High Optical Quality Y2O3 Transparent Ceramics with Fine Grain Size Fabricated by Low Temperature Air Pre-Sintering and Post-Hip Treatment

Injection Molding of Magnesium Aluminate Spinel Nanocomposites for High‐Throughput Manufacturing of Transparent Ceramics

Highly transparent MgAl0.5Ga1.5O4 ceramic for overcoming the trade-off between infrared transmittance and mechanical properties

Effect of the pre-sintering atmosphere on the microstructures and optical qualities of transparent spinel ceramics

Improved microstructure and optical properties of Nd:YAG ceramics by hot isostatic pressing

Fabrication of injection moulded translucent alumina ceramics via pressureless sintering

Influence of YOF on the preparation and optical quality of MgAl2O4 transparent ceramics

Two‐Photon Polymerization of Nanocomposites for Additive Manufacturing of Transparent Magnesium Aluminate Spinel Ceramics

Preparation of transparent MgAlON ceramics with tunable compositions

Microstructure and laser performance of fine-grained Yb:CaF 2 transparent ceramics prepared by two-step sintering

Achieving fabrication of highly transparent Y 2 O 3 ceramics via air pre‐sintering by deionization treatment of suspension

Realizing Translucency in Aluminosilicate Glass at Ultralow Temperature Via Cold Sintering Process

Preparation and characterization of MgO-Al2O3-SiO2 glass-ceramics with different MgO/Al2O3 ratio and La2O3 addition