Abstract:Magnesium aluminate spinel (MgAl2O4) ceramics are high-performance and carbon-free materials widely used in both military and civilian fields. However, it is usually challenging to densify during the solid-state sintering process. The excellent properties of some rare earth oxides have been proved to promote the densification of MgAl2O4 spinel ceramics. But the mechanism of promoting sintering is not clear. In the present work, MgAl2O4 spinel ceramics have been successfully fabricated by co-doping CeO2 and La2O3 via a single-stage solid-state reaction sintering. The effects of addition amounts of CeO2 and La2O3 on phase compositions, microstructures, sintering characteristics, cold compressive strength, and thermal shock resistance of as-prepared MgAl2O4 spinel ceramics were systematically investigated. The results show that by co-doping CeO2 and La2O3 can increase the defect concentration due to the lattice distortion. This could promote the movement of Al3+ and Mg2+ at high temperature, which is beneficial to the formation of more secondary MgAl2O4 spinel. t-ZrO2 with more Ce4+ filling between spinel grains could prevent the growth of grains and promote the densification, besides the new-formed LaAlO3 that was mainly distributed along the grain boundary of the MgAl2O4 phase, both of which were favorable for the formation of dense microstructure of MgAl2O4 spinel materials. At the same time, the formation of more secondary MgAl2O4 spinel and sintering densification also improve the mechanical properties of spinel ceramics. La3+ will segregate to the spinel grain boundary, preventing grain boundary movement and absorbing the main crack's fracture energy. With 3 wt% CeO2 and 3 wt% La2O3 co-doping, the bulk density of the sample increased from 3.02 g∙cm−3 to 3.55 g∙cm−3; the apparent porosity decreased from 12.21% to 9.97%; the cold compressive strength increased from 172.88 MPa to 189.54 MPa; and the residual strength retention ratio after thermal shock increased from 84.92% to 89.15%.

Influence of CaO on microstructure and properties of MgAl2O4 transparent ceramics

Influence of CaO content by mass in sintering aid and sintering temperature on the properties of Al2O3-based microwave ceramic materials

Optimization of Ca additive and HIP condition in fabrication of the transparent MgAl2O4 ceramics

Transparent MgAl2O4 ceramics prepared by microwave sintering and hot isostatic pressing

Effect of powder dispersity on the optical properties of HIP sintered MgAl2O4 transparent ceramics

Effect of CaO additive on the densification of MgO and MgO-YGAG:Ce ceramics

Preparation of transparent MgAlON ceramics with tunable compositions

Effect of the pre-sintering atmosphere on the microstructures and optical qualities of transparent spinel ceramics

Influence of YOF on the preparation and optical quality of MgAl2O4 transparent ceramics

Influence of Gd2O3 on the microstructure and properties of transparent MgAl2O4: Cr3+ ceramic

Highly transparent MgAl0.5Ga1.5O4 ceramic for overcoming the trade-off between infrared transmittance and mechanical properties

Fabrication of Highly Transparent Y2O3 Ceramics with CaO as Sintering Aid

The role of magnesium oxide addition in densification of AlON transparent ceramics by pressureless sintering

Magnesium aluminate spinel transparent ceramics with high optical and mechanical performance by Y3Al5O12 sintering additive

Effect of different MgO/Al2O3 ratios on microstructural densification, sintering process and mechanical property of MgAl2O4 materials

Optical and microwave dielectric properties of transparent MgAl 2O4 ceramics fabricated by Spark Plasma Sintering

Transparent Magnesium Aluminate Spinel Ceramics Reinforced by Alumina Nanofibers

Effect of Lif on the Optical Transmittance of Magnesium Aluminate Spinel

Preparation and properties of MgAl2O4 spinel ceramics by double-doped CeO2 and La2O3

Influence of LiF on the Infrared Transmissivity of Magnesia Alumina Spinel Transparent Ceramics