Abstract:Extended abstract One of the most important in situ experiments for determining rock mass fracture is a direct shear test. During this test, rock mass is loaded in two phases: in the first phase, a direct normal pressure is applied and consolidation is performed, and in the second phase, a shearing stress is applied, which leads to fracture in rock mass. After fracture is reached (peak shear strength), stress decreases and shear deformation increases [1]. In this paper a simulation of rock mass behavior during direct shear test using damage plasticity model [2,3,4] is presented. For this analysis, a three-dimensional FEM model of direct shear test with dimensions 130x80x60 m was formed. In the first phase of the FEM test normal stress corresponding to measured pressure during in situ test was applied, and in the second phase of the FEM test shear displacement corresponding to recorded displacement during in situ test was applied. In the first phase normal displacements are recorded based on calculations from the FEM model, and in the second phase shear stresses are recorded. The damage plasticity model [2,3,4] is defined by the following parameters: E 0 -Modulus of elasticity, v 0 - Poisson’s ratio, f c - uniaxial compressive strength, f t - uniaxial tensile strength, a c - pressure curve parameter, D c - degradation value for maximum compressive stress, a t - tensile curve parameter, D t - degradation value for tensile stress, G c - fracture energy for uniaxial pressure, G t - fracture energy for uniaxial tension, α p - dilatancy parameter, α - constant defining uniaxial and biaxial compressive yield stress ratio, γ - parameter for triaxial compression, l ch - characteristic size of elements, s 0 - stiffness recovery parameter, D cr - critical degradation value. Numerical simulation of direct shear test (consolidation phase and shear phase) was performed for the estimated parameters of damage plasticity model. For each step of normal stress loading, corresponding value of normal displacement was calculated, and for each step of shear displacement, corresponding value of shear stress was calculated. Based on the obtained results, it is shown that damage plasticity model can successfully simulate a complex stress state during direct shear test in rock mass. Over the entire range of applied shear displacements, shear stress increases until there is a fracture in the material (peak shear strength), and afterwards stress drop is recorded (residual shear strength).

Data-driven homogenisation of the response of heterogeneous ductile solids with isotropic damage

Modelling rock mass behaviour during direct shear stress test using damage plasticity model

A data-driven constitutive model for porous elastomers at large strains

Damage Based Constitutive Model for Predicting the Performance Degradation of Concrete

Deep Learning for Multiscale Damage Analysis via Physics-Informed Recurrent Neural Network

Numerical Simulation of Elastic Behaviour and Failure Processes in Heterogeneous Material

Effect of including damage at the tissue level in the nonlinear homogenisation of trabecular bone

Data-driven physics-constrained recurrent neural networks for multiscale damage modeling of metallic alloys with process-induced porosity

A gradient enhanced constitutive framework for the investigation of ductile damage localization within semicrystalline polymers

A finite-strain model for incomplete damage in elastoplastic materials

On Analysis of the Elasto‐viscoplastic Response of Single Crystals with Anisotropic Damage: Constitutive Modelling and Computational Aspects

Elasticity-inspired data-driven micromechanics theory for unidirectional composites with interfacial damage

On the use of constrained reactive mixtures of solids to model finite deformation isothermal elastoplasticity and elastoplastic damage mechanics

Modelling of dynamic behaviour of orthotropic metals including damage and failure

A gradient enhanced transversely isotropic damage plasticity model for rock ‐ formulation and comparison of different approaches

Numerical modeling of the evolution of ductile damage under proportional and non-proportional loading

Physically Recurrent Neural Networks for Computational Homogenization of Composite Materials with Microscale Debonding

A Heuristic Elastoplastic Damage Constitutive Modeling Method for Geomaterials: From Strength Criterion to Analytical Full-Spectrum Stress–Strain Curves

Enhanced CDM model accounting of stress triaxiality and Lode angle for ductile damage prediction in metal forming

A hybrid damage model for simulating adiabatic shear bands

A coupled ductile damage model for metal matrix composites: Development and application