Abstract:Background Comprehensive quality assurance (QA) for a seamless workflow of high‐dose‐rate brachytherapy, from imaging to planning and irradiation, is uncommon, and QA of the source dwell position is performed in one‐ or two‐dimensions. Gel dosimetry using magnetic resonance imaging (MRI) is effective in verifying the three‐dimensional distribution of doses for image‐guided brachytherapy (IGBT). However, MRI scanners are not readily accessible, and MRI scanning is time‐consuming. Nevertheless, X‐ray computed tomography (XCT) is available for IGBT planning. Purpose In this study, we designed and developed an efficient method for QA for a seamless workflow of IGBT with a new commercially available XCT‐based polymer gel dosimeter. Methods To enable direct insertion of brachytherapy applicators, the gelatinizing agent of the dosimeter was modified. A cylindrical polyvinyl chloride jar was filled with the modified gel dosimeter, which was subsequently used to determine the reproducibility of source dwell positions, detectability of source positional errors from intentionally introduced catheter length offsets, effect of looped source transfer tubes on the average displacement, extent of inter‐observer variation, and gel robustness following multiple needle‐insertions. Three ProGuide sharp needles were inserted into the jar. The dwell time at each point was determined to identify the irradiated volume with a diameter of approximately 10 mm on XCT images. All the times were the same. The plan was delivered using an afterloader with an Ir‐192 radioactive source, and the irradiated gel dosimeter was scanned using an XCT scanner. The subtracted images were generated from pre‐ and post‐irradiated images. Volumes with incremented Hounsfield units were manually identified and contoured. The centroid of the volume was defined as the measured source dwell position. Subsequently, planned source dwell positions were extracted from the DICOM file of the plan. Finally, the source dwell positions in plan and irradiated gel were compared in three axes. Results The hardness of the dosimeter was 1250% greater than that of the previously reported gel dosimeter. Source dwell positions were visually identified in the XCT image. Testing of CT acquisition, planning, irradiation, and analysis was completed in approximately 1 h. In the reproducibility test of source dwell positions, created by inserting three needles (each with three source dwell positions), the average displacements of the source positions from the first source dwell position were within 0.5 mm in all three directions. In the detectability test, displacements were less than 1 mm in the x–y plane but greater than 1 mm in the z‐axis, which was the source path direction. When errors of 1–3 mm were intentionally introduced, the measured displacement was within 0.7 mm of the median (range: 0.21–1.65 mm) of intentional errors. When the transfer tube was looped, the source dwell position displaced by approximately 1 mm. After 20 needle‐insertions, the source dwell position displacement was within 1 mm. The maximum inter‐observer variation of contouring was 0.57 mm. Conclusions The XCT‐based gel dosimeter enabled verification of three‐dimensional source dwell positions for a seamless workflow of IGBT with high precision and efficiency.

Evaluation of radiation detection sensors and quality assurance relative dosimeters fabricated using methylammonium lead iodide for brachytherapy

Feasibility assessment of polycrystalline CsPbI 3 relative dosimeters in photon and electron beam radiotherapy

Homologous Bromides Passivation of CH 3NH 3pbbr 3 Single Crystals for Photodetectors with Improved Properties

Development and evaluation of relative QA dosimeter for electron beam based on CsPbBr 3

Evaluation of photoconductor and scintillator hybrid dosimeters for radiation therapy quality assurance

Dosimetry assessment of patient-specific 3D printable materials for HDR surface brachytherapy

Automated multi-parameter high-dose-rate brachytherapy quality assurance via radioluminescence imaging

Dosimetric performance of a multi-point plastic scintillator dosimeter as a tool for real-time source tracking in high dose rate brachytherapy

Three‐dimensional source position verification in image‐guided high‐dose‐rate brachytherapy using an XCT‐based gel dosimeter

Radiation-Tolerant Proton Detector Based on the MAPbBr3 Single Crystal

Use of Thermoluminescence Dosimetry for QA in High-Dose-Rate Skin Surface Brachytherapy with Custom-Flap Applicator

High Sensitivity X-Ray Detectors with Low Degradation Based on Deuterated Halide Perovskite Single Crystals

Evaluation of a complementary metal oxide semiconductor detector as a tool for stereotactic body radiotherapy plan quality assurance

Radiation Tolerance of Organohalide-Based Perovskite Solar Cells under 6 MeV Electron Beam Irradiation

Quality assurance measurements for high-dose-rate brachytherapy without film

Low-cost flexible thin-film detector for medical dosimetry applications

3D in vivo dosimetry of HDR gynecological brachytherapy using micro silica bead TLDs

Performance assessment of a 2D array of plastic scintillation detectors for IMRT quality assurance

A study on absorbed dose measurement using a butyl acrylate-based plastic scintillator as a tissue-equivalent detector

Flexible Polymer X-ray Detectors with Non-fullerene Acceptors for Enhanced Stability: Toward Printable Tissue Equivalent Devices for Medical Applications

X-rays sensing properties of MEH-PPV, Alq₃ and additive components: a new organic dosimeter as a candidate for minimizing the risk of accidents of patients undergoing radiation oncology