Abstract:Inorganic CsPbIBr2 perovskite has been considered as a promising light-absorbing material for solar cells due to its high stability and suitable bandgap. Although the remarkable improvement of CsPbIBr2 PSC has been achieved, the efficiency of this cell is still lower than those of other analogues and far below its theoretical limit. This is mainly due to the serious charge recombination in the as-fabricated CsPbIBr2 cells derived from the poor-quality CsPbIBr2 perovskite film with a large quantity of defects and numerous grain boundaries. Therefore, fabricating high-quality CsPbIBr2 perovskite film is a key factor for the further efficiency improvement of CsPbIBr2 PSCs. Herein, phenylthiourea (PTU) additive is introduced into the CsPbIBr2 precursor to tailor the crystallization of CsPbIBr2 perovskite for fabricating high-quality CsPbIBr2 perovskite. The C=S group of PTU can coordinate with PbBr2 in the precursor owing to the lone-pair electrons on S and the empty orbits of Pb2+. The strong interaction between PTU and the CsPbIBr2 precursor components can form PTU·Pb···Br(I) intermediate phase in the precursor upon PTU introduction. The PTU·Pb···Br(I) intermediate phase can reduce the nucleation rate of perovskite and modulate the perovskite crystal growth because the extra energy is required to break the strong coordination bond in the intermediate phase, resulting in a low crystallization rate of CsPbIBr2 perovskite. Such a retardation of perovskite crystallization is conducive to the formation of high-crystallinity perovskite film with smooth surface, large crystal grains, high crystallization, and low density of defect. Meanwhile, the decomposition of PTU during thermal annealing makes the S2– inserted into interstitial of CsPbIBr2 crystal lattice, which greatly enhance the stability of CsPbIBr2 perovskite. The carbon-based PSCs with a normal n-i-p structure of FTO/compact-TiO2 layer/meso-TiO2 layer/perovskite film/carbon layer are fabricated, and their photovoltaic performances are measured under a simulated AM1.5 illumination (100 mW·cm–2). The PSC based on PTU-CsPbIBr2 perovskite delivers a high power conversion efficiency of 10.09%, which is much higher than that of the control device. This great improvement of photovoltaic performance can be attributed to the largely promoted perovskite quality, which enhances the charge collection and suppresses the charge recombination in the device. In addition, the unencapsulated device preserves 82% of the initial efficiency after being stored under ambient condition for 35 days, suggesting excellent stability. Therefore, this work provides an effective complementary strategy for effectively improving the performance of inorganic PSCs.

Enhanced efficiency of CsPbIBr2 perovskite solar cells through dual-layer ETL engineering

Enhancing the structural, and optoelectronic properties of double ETL Nickel doped CsPbIBr2 perovskite solar cell

Significant performance enhancement of all‐inorganic CsPbBr 3 perovskite solar cells enabled by Nb‐doped SnO 2 as effective electron transport layer

Enhanced Performance of Carbon-Based Planar CsPbBr3 Perovskite Solar Cells with Room-Temperature Sputtered Nb2O5 Electron Transport Layer

Efficient carbon-based planar CsPbBr<sub>3</sub> perovskite solar cells with Li-doped amorphous Nb<sub>2</sub>O<sub>5</sub> layer

Enhanced Electron Extraction Using Neodymium Ions Doped TiO2 for All-Inorganic CsPbBr3 Perovskite Solar Cells

Synergistic Effect of Surface p-Doping and Passivation Improves the Efficiency, Stability, and Reduces Lead Leakage in All-Inorganic CsPbIBr<sub>2</sub>-Based Perovskite Solar Cells

Interface‐Modification‐Induced Gradient Energy Band for Highly Efficient CsPbIBr 2 Perovskite Solar Cells

Achieving high-performance planar perovskite solar cell with Nb-doped TiO2 compact layer by enhanced electron injection and efficient charge extraction

Numerical Simulation of All Inorganic CsPbIBr2 Perovskite Solar Cells with Diverse Charge Transport Layers using DFT and SCAPS-1D Frameworks

Uniform Stepped Interfacial Energy Level Structure Boosts Efficiency and Stability of CsPbI2Br Solar Cells

Uniform Stepped Interfacial Energy Level Structure Boosts Efficiency and Stability of CsPbI 2 Br Solar Cells

Enhancing the Optical, Morphological and Electronic Properties of the Solution-Processed CsPbIBr2 Films by Li Doping for Efficient Carbon-Based Perovskite Solar Cells

Performance Enhancement of Hole Transport Layer-Free Carbon-Based CsPbIBr2 Solar Cells through the Application of Perovskite Quantum Dots

Tailoring of CsPbIBr2 Perovskite Crystallization Via Phenylthiourea for Stable and Efficiency Perovskite Solar Cells

Optimized Interface and Recrystallized Grains by CsBr Treatment for Enhanced Photovoltaic Performance of Perovskite Solar Cells

Efficient All-Inorganic CsPbIBr2 Perovskite Solar Cells with an Open Voltage over 1.33 V by Dual-Additive Strategy

n-type absorber by Cd2+ doping achieves high-performance carbon-based CsPbIBr2 perovskite solar cells

Double‐Side Interface Engineering Synergistically Boosts the Efficiency of Inorganic CsPbIBr2 Perovskite Solar Cells over 12%

High‐Efficiency Carbon‐based CsPbI2Br Perovskite Solar Cells from Dual Direction Thermal Diffusion Treatment with Cadmium Halides

Achieving 17.46% Efficiency CsPbI2Br Perovskite Solar Cells via Multifunction Lead Chloride‐Modified ZnO Electron Transporting Layer