Abstract:The use of high strength low alloy steels provides several potential advantages including lower weight, lower manufacturing costs, and ease of handling and transport. The progress in steel manufacturing technology has continually called for new developments in welding processes and consumables to produce weld metal deposits with mechanical properties essentially equivalent to the base metal. Controlling the weld metal microstructures as well as raising the welding productivity is critical factor for the development of weld metal of high strength steel to secure satisfactory mechanical properties and to reduce production costs. In order to meet the demand to apply 1000 MPa class steel to the fabrication of large scale steel structures, a weld wire for the 1000 MPa class steel has been under development to obtain the required strength and toughness, which depend primarily on the microstructure. In this work, the effects of shielding gas composition on the microstructure and properties of 1000 MPa grade deposited metals produced by metal active gas (MAG) welding have been investigated. The shielding gas employed was a mixture of argon (Ar) and carbon dioxide (CO2) (5%similar to 30%), and the weld heat input was 13 kJ/cm. The properties of deposited metal with shielding gas of 80%Ar+20%CO2 is the best, the yield strength is 980 MPa, meanwhile, its Charpy absorbed energy at room temperature and -40 degrees C are 72.6 and 52 J, respectively. The results show that the microstructure of the deposited metal, consisting primary of low carbon martensite and a few parallel bainite plate, became more interweaved bainitic packets as the CO2 content of the shielding gas was increased. The initial bainite nucleated at austenite grain boundaries and subsequent bainite plates can form at the oxide inclusions of intragranular, which presented an intersected configuration and the microstructure was refined. The content of bainite palte and distribution morphology of martensite/bainite is the intrinsic reason attributed to mechanical properties of deposited metals. The content of bainite for deposited metal has an optimal proportion and more isn't necessarily better. It was also found that the area fraction, the size and the compositions of oxide inclusions in deposited metals were changed with increasing CO2 content. The deposited metal as using 70%Ar+30%CO2 has the minimum toughness because more large size oxide inclusions formed which are known to be harmful to the toughness.

A novel liquid-shielded welding solution for diffusible hydrogen content restriction and metal transfer controlling in underwater FCAW condition

A novel approach of ultra-low diffusible hydrogen welding wire for underwater wet flux-cored arc welding: a spontaneous barrier of molten slag

Flux cored arc welding of 304L stainless steel within glycerol environment

Weld Zone Analysis Based on FCAW Mechanical Characteristics and Heat Transfer Analysis of 316L Stainless Steel for Liquefied Hydrogen Tanks

A novel approach to optimize weld formation and regulate interfacial microstructure in TC4/304SS dissimilar arc welding by active hybrid shielding gas

Influence of Shielding Gas on Microstructure and Properties of GMAW DSS2205 Welded Joints

Hydrogen embrittlement behavior in the nugget zone of friction stir welded X100 pipeline steel

Hydrogen diffusion simulation of the X80 pipeline steel girth weld zone considering the synergistic effect of the structure–stress–concentration field

Effect of Shielding Conditions on Welding Properties in Underwater Local-Dry Laser Welding

Operational performance and metal droplet formation in pulsed-shielded metal arc underwater welding

Effect of Shielding Gas on Surface Formation During Laser Welding of Al-Si Coated Press-Hardened Steels

Fluorinated Siloxane Modified Layered Double Hydroxide Sealing Film to Enhance the Corrosion Resistance of Anodic Oxide Film of Fricition Stir Welding Joint of Aluminum Alloys

An Innovative Methodology in Narrow Gap GTAW for Alternating Magnetic Field with Synchronous Swing of Filler Wire and Arc

Preparation and Hydrogen Barrier Property of FexAly/Al/Al2O3 Composite Coating on X80 Steel Surface

EFFECT OF SHIELDING GAS ON MICROSTRUCTURE AND PERFORMANCE OF 1000 MPa GRADE DEPOSITED METALS

Improvement of microstructure and mechanical properties for underwater wet 16Mn/304L dissimilar steel welded joints assisted by presetting butter layer

Designing functionalized graphene-stitched-SiC/fluoropolymer novel composite coating with excellent corrosion resistance and hydrogen diffusion barrier properties

Effect of Nitrogen‐Added Shielding Gas on Microstructure Evolution of Welded Joints by Gas Tungsten Arc Welding Process in Duplex Stainless Steel 2205

Effect of liquid column on process stability and weld formation under ultra-high power fiber laser-arc hybrid welding of thick plates

Effect and mechanism of ionic liquid-polymer composite coating on enhancing hydrogen embrittlement resistance of X80 pipeline steel for hydrogen blended natural gas transportation

Effect of polarities and shielding gases in CWW GMAW