Abstract:Statement of problem. Digital techniques are not clinically applied for 1-piece maxillary prostheses containing an obturator and removable partial denture retained by the remaining teeth because of the difficulty in obtaining sufficiently accurate 3-dimensional (3D) images. Purpose. The purpose of this pilot clinical study was to generate 3D digital casts of maxillary defects, including the defective region and the maxillary dentition, based on multisource data registration and to evaluate their effectiveness. Material and methods. Twelve participants with maxillary defects were selected. The maxillofacial region was scanned with spiral computer tomography (CT), and the maxillary arch and palate were scanned using an intraoral optical scanner. The 3D images from the CT and intraoral scanner were registered and merged to form a 3D digital cast of the maxillary defect containing the anatomic structures needed for the maxillary prosthesis. This included the defect cavity, maxillary dentition, and palate. Traditional silicone impressions were also made, and stone casts were poured. The accuracy of the digital cast in comparison with that of the stone cast was evaluated by measuring the distance between 4 anatomic landmarks. Differences and consistencies were assessed using paired Student t tests and the intraclass correlation coefficient (ICC). In 3 participants, physical resin casts were produced by rapid prototyping from digital casts. Based on the resin casts, maxillary prostheses were fabricated by using conventional methods and then evaluated in the participants to assess the clinical applicability of the digital casts. Results. Digital casts of the maxillary defects were generated and contained all the anatomic details needed for the maxillary prosthesis. Comparing the digital and stone casts, a paired Student t test indicated that differences in the linear distances between landmarks were not statistically significant (P >.05). High ICC values (0.977 to 0.998) for the interlandmark distances further indicated the high degree of consistency between the digital and stone casts. The maxillary prostheses showed good clinical effectiveness, indicating that the corresponding digital casts met the requirements for clinical application. Conclusions. Based on multisource data from spiral CT and the intraoral scanner, 3D digital casts of maxillary defects were generated using the registration technique. These casts were consistent with conventional stone casts in terms of accuracy and were suitable for clinical use.

Feasibility study of a novel digital template-guided flapless extraction for maxillary palatal impacted teeth

3D-printed titanium surgical guides for extraction of horizontally impacted lower third molars

Precise extraction of impacted supernumerary tooth in the maxillary anterior region with a digital guide plate: A case report

Digital robot-assisted minimally invasive impacted tooth extraction: A case report

A comparative study of the application of three digital imaging techniques to assess the thickness of the palatal mucosa of the maxillary anterior teeth

3D Printing of Drill Guide Template for Access Cavity Preparation in Human Molars: a Preliminary Study

Application of Three-Dimensional Printing Technology in Oral and Maxillofacial Reconstruction

Applying Computer Techniques in Maxillofacial Reconstruction Using a Fibula Flap: a Messenger and an Evaluation Method.

Exploratory study on a novel minimally invasive tunnel like flap approach for orthodontic movement of dental implants

A New Procedure Assisted by Digital Techniques for Secondary Mandibular Reconstruction with Free Fibula Flap

Triple digital guides for implant-supported restorations with alveoloplasty procedure in the esthetic zone

[New intraoral digital impression with pneumatic gingival retraction used in the restoration of crown for posterior teeth: a case report]

A Minimally Invasive Extraction Technique Using Benex Extraction System in Flapless Immediate Implant Placement in Anterior Teeth

A Digital Technique for Occlusal Design of a Posterior Full Crown Based on Physiological Tooth Displacement and Occlusion of Adjacent Teeth.

Generation and evaluation of 3D digital casts of maxillary defects based on multisource data registration: A pilot clinical study.

A Digital Technique for Fabricating Implant-Supported Interim Restorations in the Esthetic Zone.

Digital planning protocol for functional and esthetic prosthetic treatment

Visual treatment objective-based lateral esthetics preview for implant-supported reconstruction in terminal dentition with proclined maxillary incisors

Digitally printed custom trays assembled with occlusion rims and gothic arch tracing devices attached with tenon-and-mortise joints for biofunctional complete dentures: A dental technique

A Fully Digital Workflow for Prosthetically Driven Alveolar Augmentation with Intraoral Bone Block and Implant Rehabilitation in an Atrophic Anterior Maxilla.

A digital workflow for fabricating a mandibular guide plane prosthesis for patients about to undergo hemimandibulectomy: A dental technique