Abstract:The effects of nanosized reinforcement particles on precipitation reactions in age-hardenable Al alloy matrix composites have been largely unknown. In this work, an Al-Zn-Mg-Cu matrix composite reinforced with uniformly distributed TiB2 nanoparticles was successfully produced. The solid-soluted, peak-aged and overaged materials were then characterized, at the atomic scale using (high-resolution) scanning transmission electron microscopy, to provide a fundamental insight into the interface precipitation. Our results demonstrated that the facetted TiB2 nanoparticles have a significant impact on the precipitation in matrix areas adjacent to the TiB2/Al interfaces. The interfaces after solid-solution treatment are tightly-bonded and oxide-free, and display two orientation relationships (ORs): the well-reported [21¯1¯0]TiB2//[101]Al, (0001)TiB2//(1¯11)Al (OR1) and the new [21¯1¯0]TiB2//[101]Al, (011¯0)TiB2//(111¯)Al (OR2). The interface precipitates (i.e. interphase) having the size of several tens of nanometers were formed after ageing and were determined to be (Zn1.5Cu0.5)Mg phase. Their formations were only related to the initial OR1 and OR2 where the mutual ORs between the TiB2, interphase and Al matrix were further developed. Periodically spaced misfit dislocations were revealed at the semi-coherent TiB2/Al interfaces, which are generally considered beneficial to the heterogeneous precipitation. They not only reduced nucleation energy barrier, but also acted as short-circuit diffusion paths for transporting solute atoms and vacancies, accelerating growth rate. However, the growth of interphase at the interface parallel to close-packed {111} Al planes was suppressed by the ultra-low accommodation factor. In addition, such an interface precipitation reduced the mismatch of the TiB2/Al interface, increasing the overall coherency and being potential for effective interface strengthening.

On the novel precipitation sequence of the TiN modified Al-Mn-Sc alloy processed by laser powder bed fusion

Investigation on the Microstructure and Mechanical Behaviors of a Laser Formed Nb-Ti-Al Alloy

Microstructure evolution and strengthening mechanisms of a high-performance TiN-reinforced Al-Mn-Mg-Sc-Zr alloy processed by laser powder bed fusion

Precipitation Behaviors and Properties of Solution-Aging Al-Zn-Mg-Cu Alloy Refined with TiN Nanoparticles

Engineering fine grains, dislocations and precipitates for enhancing the strength of TiB 2 -modified CoCrFeMnNi high-entropy alloy using Laser Powder Bed Fusion

In-situ Synthesis of TiN and its Effects on Fe-12Cr-6Al in Laser Powder Bed Fusion

Structural transformation behavior in a high Nb–TiAl alloy additively manufactured by laser powder bed fusion

Achieving grain refinement and ultrahigh yield strength in laser aided additive manufacturing of Ti−6Al−4V alloy by trace Ni addition

Fabrication of Ti3Al-Based Intermetallic Alloy by Laser Powder Bed Fusion Using a Powder Mixture

Microstructure and Properties of TiN-reinforced W–Ti Alloys Prepared by Spark Plasma Sintering

Achieving superior strength-ductility combination in the heterogeneous microstructured Ti64 alloy via multi-eutectoid elements alloying with CoCrFeNiMn during laser powder bed fusion

Enhancing Hardness and Wear Performance of Laser Additive Manufactured Ti6Al4V Alloy Through Achieving Ultrafine Microstructure

Microstructure and Mechanical Properties of a Novel Al-Mg-Sc-Ti Alloy Fabricated by Laser Powder Bed Fusion

Microstructure of a Ti–50 Wt% Ta Alloy Produced Via Laser Powder Bed Fusion

Effect of heat treatment on precipitation behavior and mechanical properties of FeCrNi-based medium entropy alloy fabricated by additive manufacturing

Microstructure and mechanical properties of laser additive manufactured novel titanium alloy after heat treatment

Atomic-scale investigation of the interface precipitation in a TiB2 nanoparticles reinforced Al–Zn–Mg–Cu matrix composite

Grain boundary α-phase precipitation and coarsening: Comparing laser powder bed fusion with as-cast Ti-6Al-4V

Synergistic Strengthening Mechanisms of Dual-Phase (TiN+AlN) Reinforced Aluminum Matrix Composites Prepared by Laser Powder Bed Fusion

Microstructural Evolution of a High-Strength Zr-Ti-Modified 2139 Aluminum Alloy for Laser Powder Bed Fusion

Laser Powder Bed Fusion of Titanium Aluminides: An Investigation on Site-Specific Microstructure Evolution Mechanism