Abstract:Triboelectric nanogenerators (TENGs) have gained considerable attention for harnessing and converting low frequency mechanical energy into electrical energy. Methodologies for development of TENGs are evolving from manual traditional fabrication to advanced three‐dimensional (3D) printing technology. Enhancement of surface charge production of TENGs by increasing the contact area is a pivotal challenge. Surface patterning of triboelectric layers is an effective approach for improving the surface area and charge production. This study initially investigates the performance of contact separation and sliding modes of TENGs using COMSOL Multiphysics simulation environment. Output analysis is performed to identify the best material combination and surface patterns for triboelectric layers. Polyamide 12 (PA12) and Vero clear pair outperformed all tested 3D printable triboelectric materials in simulation environment. The output performance of a plain surface TENG is then compared with square, rectangular and pyramid patterned TENGs. The pyramid pattern emerged as the most efficient geometry, demonstrating a solid output of 95.8V Voc and 0.99 μA Isc. Advanced 3D printing techniques including powder based multi jet fusion (MJF) and resin‐based poly jet fusion (PJF) are utilized to print PA12 and Veroclear, respectively. Laser surface patterning (LSP) technique is used to make precise micropatterns on the surfaces of the Veroclear and PA12 layers, resulting in a consistent and effective surface morphology that enhances the surface area of triboelectric layers, and outperforms traditional approaches of patterning in consistency and efficacy. The validation of simulation results is made where the pyramid pattern is emerged as the most efficient geometry experimentally. Performance was maintained with minimal degradation after 102 cycles, and a 22μF‐63V capacitor was successfully used to store the generated charge. This study not only sets the path for pre‐experimental analysis using simulation environment, but also provides a clear demonstration of advanced manufacturing techniques for printing and patterning 3D printed triboelectric materials. This article is protected by copyright. All rights reserved.

Output Enhancement of a 3D Printed Triboelectric Nanogenerator Using Laser Surface 3D Patterning

Enhancement of Patterned Triboelectric Output Performance by an Interfacial Polymer Layer for Energy Harvesting Application

Enhancement of Triboelectric Nanogenerator Output Performance by Laser 3D-Surface Pattern Method for Energy Harvesting Application

Integrated and Shape-Adaptable Multifunctional Flexible Triboelectric Nanogenerators Using Coaxial Direct Ink Writing 3D Printing

A PDMS-Al Triboelectric Nanogenerator Using Two-Pulse Laser to Enhance Effective Contact Area and Its Application

Nano Groove and Prism-Structured Triboelectric Nanogenerators

Effect of Surface and Contact Points Modification on the Output Performance of Triboelectric Nanogenerator

Enhanced Triboelectric Output of PDMS-based Composite Film with Bi-Material Filling and Surface Patterning

Carbon Electrodes Enable Flat Surface PDMS and PA6 Triboelectric Nanogenerators to Achieve Significantly Enhanced Triboelectric Performance

Investigated a Pll Surface-Modified Nylon 11 Electrospun as a Highly Tribo-Positive Frictional Layer to Enhance Output Performance of Triboelectric Nanogenerators and Self-Powered Wearable Sensors

Enhancing Performance of Composite-Based Triboelectric Nanogenerators Through Laser Surface Patterning and Graphite Coating for Sustainable Energy Solutions

Enhancing the Output Performance of a Triboelectric Nanogenerator Based on Modified Polyimide and Sandwich-Structured Nanocomposite Film

Some measures to enhance the energy output performances of triboelectric nanogenerators

Development of the Triboelectric Nanogenerator Using a Metal-to-Metal Imprinting Process for Improved Electrical Output

Engineering of electrodes with 2D Ti3C2Tx-MXene sheets and chloride salt for robust and flexible high electrical power triboelectric nanogenerator

Contact Electrification Spectrum for Performance Enhancement Mechanism Investigation of Triboelectric Nanogenerators based on Silicone Elastomers with Different Surface Microstructures

Large‐Area Direct Laser‐Shock Imprinting of a 3D Biomimic Hierarchical Metal Surface for Triboelectric Nanogenerators

High-performance triboelectric nanogenerators with laser-induced graphene pattern for efficient charge transfer

Influence of Thickness and Contact Area on the Performance of PDMS-Based Triboelectric Nanogenerators

Development of flexible high-performance PDMS-based triboelectric nanogenerator using nanogratings

High-Performance Triboelectric Nanogenerator with Double-Surface Shape-Complementary Microstructures Prepared by Using Simple Sandpaper Templates