Abstract:Converting solar energy into power and hydrogen provides a promising pathway to fulfilling instantaneous electricity demand (power generation) as well as continuous demand via storing energy in chemical bonds (hydrogen generation). Co-generation of power and hydrogen is of great interest due to its potential to overcome expensive electricity storage in conventional PV plus battery systems. Both solar thermochemistry processes and photo-electrochemical cells (PECs) are extensively explored technologies to produce solar hydrogen. The key challenges for solar thermochemistry processes are extremely high operating temperature (~ 1500 oC) and low demonstrated efficiency (< 1% for hydrogen generation). For PECs, the limited solar absorption together with sluggish electrochemical reactions, especially for OER, leads to limited theoretical solar fuel generation. Operating PECs at high temperature will lead to decreased photovoltage and interface stability. Inspired by the thermally regenerative batteries, we propose a photo-thermo-electrochemical (PTEC) device that uses the solid oxide-based moderate high temperature cell (~1000 ℃) as the photo-absorber for simultaneously converting concentrated solar radiation into heat and generating fuel or power electrochemically driven by the discharging power from the low temperature cell (~700 ℃). PTEC device enables full solar spectrum utilization, highly favorable thermodynamics and kinetics, and cost-effectiveness. A continuous PTEC device has two working modes, which are voltage differential (VD) mode and current differential (CD) mode. The current-voltage characteristics of a PTEC device are shown in Figure 1. It mainly consists of five parts. A high temperature cell (HTC) serves as a solar absorber and a low temperature cell (LTC) serves as heat recovery. Besides, the opposite electrochemical reactions take place in two cells meaning that HTC and LTC can also function as a hydrogen production as well as an electricity generator component, respectively. Heat exchanger(s) is placed between the HTC and LTC and hot fluids pass through a heat exchanger before entering LTC to reduce heat losses to environment as well as reducing input solar energy. The VD mode and CD mode can be realized in PTECs via controlling of DC-DC converter. In order to identify the main parameters, we develop a multi-physics model based on finite element method, including mass, heat and charge transfer, and electrochemical reactions. In addition, heat exchange is modeled by solving energy balance equation, DC-DC convertor is assumed by constant efficiency, and a lumped parameter model is used to describe solar receiver including energy losses of conduction and reradiation. This framework also allows us to provide design guidelines for PTEC devices with high solar-to-electricity (STE) efficiency and solar-to-hydrogen (STH) efficiency. The maximum STE and STH efficiency under reference conditions of PTEC device was found to be 4 % and 2 %. A further improved performance in terms of STE and STH efficiency are about 19 % and 16 %, respectively, via optimizing temperature configuration between HTC and LTC and material properties. It is also interesting to note that STH can reach higher than 80 % of STE at a large temperature difference, which shows a promising energy storage device by storing excessive electrical power in form of hydrogen. The main results show that the temperature of HTC and efficiency of heat exchange are key parameters to optimize PTEC efficiency. The performance of DC-DC convertor dominates STH efficiency. Besides, ionic conductivity of electrolyte can contribute to significantly expanding the operating current density range. The PTEC is a promising technology for solar energy conversion and storage as it is able to produce electricity and hydrogen in a single device. The solar conversion efficiency predicted with our numerical model supports that by optimizing the design and operational conditions, this technology can compete with existing solar fuel pathways. Figure 1

All-in-One, Solid-State, Solar-Powered Electrochemical Cell

Fully solar-powered photoelectrochemical conversion for simultaneous energy storage and chemical sensing.

Simultaneous Photoelectrocatalytic Water Oxidation and Oxygen Reduction for Solar Electricity Production in Alkaline Solution.

Flexible Electrolyte and Cathode Membranes for All-Solid-State Batteries Fabricated by a One-Step Solvent Method

6.16% Efficiency of Solid-State Fiber Dye-Sensitized Solar Cells Based on LiTFSI Electrolytes with Novel TEMPOL Derivatives

A Stabilized, Intrinsically Safe, 10% Efficient, Solar‐Driven Water‐Splitting Cell Incorporating Earth‐Abundant Electrocatalysts with Steady‐State Ph Gradients and Product Separation Enabled by a Bipolar Membrane

Solution-processed Nanoporous NiO-dye-ZnO Photocathodes: Toward Efficient and Stable Solid-State P-Type Dye-Sensitized Solar Cells and Dye-Sensitized Photoelectrosynthesis Cells

Complete solar-driven dual-photoelectrode fuel cell for water purification and power generation in the presence of peroxymonosulfate

Hydrogen from wet air and sunlight in a tandem photoelectrochemical cell

Photo-assisted (de)lithiation to Enhance Photoelectrochemical Storage in Quasi-Solid-state Li-ion Batteries

Bi/Bi2O3/TiO2 Heterojunction Photocathode for High-Efficiency Visible-Light-driven Lithium-Sulfur Batteries: Advancing Light Harvesting and Polysulfide Conversion

Flexible Composite Solid Electrolyte with an Active Inorganic Filler

Highly Integrated Perovskite Solar Cells‐Based Photorechargeable System with Excellent Photoelectric Conversion and Energy Storage Ability

A Portable and Efficient Solar‐Rechargeable Battery with Ultrafast Photo‐Charge/Discharge Rate

Integration of Inverse Nanocone Array Based Bismuth Vanadate Photoanodes and Bandgap-Tunable Perovskite Solar Cells for Efficient Self-Powered Solar Water Splitting

(Digital Presentation) Photo-Thermo-Electrochemical Cells for On-Demand Solar Power and Hydrogen Generation

Unassisted Photoelectrochemical Cell with Multimediator Modulation for Solar Water Splitting Exceeding 4% Solar-to-Hydrogen Efficiency

Wireless portable light-weight self-charging power packs by perovskite-organic tandem solar cells integrated with solid-state asymmetric supercapacitors

An All-Inorganic Perovskite Solar Capacitor for Efficient and Stable Spontaneous Photocharging

An efficient and stable solar flow battery enabled by a single-junction GaAs photoelectrode

Ionic Liquid Gel Microspheres As Multifunctional Bi-Component Additives for the Crystallinity Manipulation and Defect Passivation in All-Air-processed Perovskite Solar Cells