Chang-Guang Zhou,Shi-Hao Ren,Hu-Tian Feng,Jun-Wan Shen,Yi-Shen Zhang,Zeng-Tao Chen
Abstract:<p>The degradation of the preload gradually deteriorates the dynamic behavior of linear rolling guide (LRG) as well as the machine tool it drives. However, very few researches can be found on the preload degradation of LRG. In the present work, a preload degradation model for LRG is proposed, in which two effectiveness coefficients are introduced accounting for both the micro-contact behavior and the intermittent wear behavior between the rolling element and raceway. The preload degradation model is verified experimentally using two specially designed test benches. The preload predicted by the current model agrees better with the experimental results than that obtained by previous studies. The numerical simulation results show that the rate of preload loss of the linear rolling guide increases with the increase of the external load <span class="math"><math>FV</math></span>, running speed <span class="math"><math>VC</math></span> and fractal parameter <span class="math"><math>G</math></span>, and the decrease of the fractal parameter <span class="math"><math>D</math></span>, and their effects on the rate of preload loss can be ranked from strongest to weakest as <span class="math"><math>VC</math></span><span class="math"><math>D</math></span>, <span class="math"><math>FV</math></span> and<span class="math"><math>G</math></span>.</p>
What problem does this paper attempt to address?
The problem that this paper attempts to solve is the pre - load degradation problem of the Linear Rolling Guide (LRG). Specifically, due to the sliding wear behavior between the rolling elements and the guide rail, the pre - load of the LRG will gradually decrease, which will lead to a significant deterioration in the dynamic performance of CNC machine tools. However, there are relatively few studies on LRG pre - load degradation. Therefore, this paper proposes a new pre - load degradation model, aiming to more accurately predict the pre - load change of the LRG in actual operation.
### Main research contents:
1. **Define pre - load**:
- The pre - load is defined as the resultant force of the normal contact loads of the balls moving upward (i = 1, 3) or downward (i = 2, 4) in the vertical axis direction.
- The initial pre - load \(F_{p0}\) is represented by the formula \(F_{p0}=\sum_{j = 1}^{n}(Q_{01j}^{(b,c)}\cos\gamma_1+Q_{03j}^{(b,c)}\cos\gamma_3)=\sum_{j = 1}^{n}(Q_{02j}^{(b,c)}\cos\gamma_2+Q_{04j}^{(b,c)}\cos\gamma_4)\).
2. **Wear mechanism analysis**:
- Analyzed the wear mechanism between the rolling elements and the guide rail, and established models for calculating the wear volume, contact load, sliding speed and wear depth.
- The wear depth \(\Delta\delta_{ij}^{(b,n')}\) can be calculated by the formula \(\Delta\delta_{ij}^{(b,n')}=\frac{W_{ij}^{(b,n')}}{A_{ij}^{(b,n')}}\), where \(W_{ij}^{(b,n')}\) and \(A_{ij}^{(b,n')}\) represent the wear volume and contact area between the \(j\) - th rolling element and the \(i\) - th guide rail respectively.
3. **Contact area calculation**:
- Used fractal theory to characterize the microscopic contact characteristics of rough surfaces, and introduced a contact coefficient \(\lambda\) to consider the influence of curved surface contact.
- The contact area \(A_{ij}^{(b,n')}\) is calculated by the formula \(A_{ij}^{(b,n')}=\lambda\int_{0}^{a_L}n(a)da=\lambda\frac{D}{2 - D}a_L\).
4. **Pre - load degradation model**:
- Considering the intermittent wear behavior of the LRG, a correction coefficient \(K'_{n'i}\) was introduced to correct the wear model.
- Finally, a new pre - load degradation prediction model was constructed, which explicitly expresses the change of pre - load over time.
### Experimental verification:
- Verified the proposed pre - load degradation model through experiments. The experimental results show that the prediction results of this model are closer to the actual measured values than previous studies.
### Influence factor analysis:
- Numerical simulation results show that the increase of external load \(F_V\), running speed \(V_C\) and fractal parameter \(G\), and the decrease of fractal parameter \(D\) will all lead to an increase in the pre - load loss rate. The influence of these factors on the pre - load loss rate from strong to weak is \(V_C\), \(D\), \(F_V\) and \(G\) in turn.
In conclusion, this paper provides a theoretical basis for more accurate monitoring and prediction of the dynamic behavior of the LRG by establishing a new pre - load degradation model, which is helpful to improve the accuracy and reliability of CNC machine tools.