Abstract:Thermoelectric (TE) energy conversion technology provides a promising way to improve the efficiency of fossil energy by generating electricity from low-grade waste heat. With regard to these applications, thermoelectric generators (TEGs) should be designed from system integration perspectives to simultaneously improve heat transfer efficiency and system simplification as well as the robust mechanical properties. However, typical TEGs fabricated by conventional methods barely accomplish such requirements. Herein, high-quality TEGs were assembled by combining the well-flowable spherical bismuth telluride (BT) powdered precursors and selective laser melting (SLM) technology. By optimizing the electronic and phonon transport properties through defect engineering driven by 3D printing, a high figure of merit was accomplished for 1.27 (p-type) and 1.13 (n-type) in BT. This achievement is primarily attributed to the nonequilibrium solidification mechanism, which leads to the formation of multiscale defects during the 3D printing process. The introduction of these multiscale defects enables the effective scattering of wide frequency phonons, leading to a substantial reduction in lattice thermal conductivity. Meanwhile, robust mechanical properties were obtained in the printed p-type/n-type BT TE materials parallel to the building direction (BD) with a compressive strength reaching 257/250 MPa by employing the fine grain structure and the high density of nanotwins introduced during the SLM process. A well shape-controllable and high-performance TEG was designed using 3D-printed BT half-rings, and an output power of 134 mW was achieved at a temperature gradient of 38.9 °C. Our study opens a new route for the great potential of TE materials based on standard commercial SLM 3D printing technology for low-grade waste heat emitted from structures with heterogeneous shapes.

Broad Temperature Plateau for High Thermoelectric Properties of n-Type Bi 2 Te 2.7 Se 0.3 by 3D Printing-Driven Defect Engineering

3D Printing of Bi2Te3-Based Thermoelectric Materials with High Performance and Shape Controllability

Realizing High-Efficiency Thermoelectric Module by Suppressing Donor-Like Effect and Improving Preferred Orientation in N-Type Bi2(Te, Se)3

High‐Performance Industrial‐Grade p‐Type (Bi,Sb)2Te3 Thermoelectric Enabled by a Stepwise Optimization Strategy

Defect Engineering Stabilized AgSbTe2 with High Thermoelectric Performance

High-Performance p-Type Bi 2 Te 3 -Based Thermoelectric Materials Enabled via Regulating Bi-Te Ratio

Broad-Temperature Thermoelectric Figure of Merit Enhancement in Unconventional n-Type Bi 2 Te 2.3 Se 0.7 Alloys

High-performance near-room-temperature n-type Bi2Te3-based thermoelectric alloys with superior mechanical properties

Synergistically enhanced thermoelectric and mechanical performance of Bi 2 Te 3 via industrial scalable hot extrusion method for cooling and power generation applications

Large-scale SHS based 3D printing of high-performance n-type BiTeSe: Comprehensive development from materials to modules

Enhanced Electrical Transport Properties via Defect Control for Screen-Printed Bi2Te3 Films over a Wide Temperature Range

Hierarchical Low-Temperature n-Type Bi2Te3 with High Thermoelectric Performances

Achieving High Thermoelectric Performance of n-Type Bi 2 Te 2.79 Se 0.21 Sintered Materials by Hot-Stacked Deformation

Multi-scale hierarchical microstructure modulation towards high room temperature thermoelectric performance in <i>n</i>-type Bi<sub>2</sub>Te<sub>3</sub>-based alloys

Point Defect Engineering of High‐Performance Bismuth‐Telluride‐Based Thermoelectric Materials

Enhancing Thermoelectric Performance of N-Type Hot Deformed Bismuth-Telluride-Based Solid Solutions by Nonstoichiometry-Mediated Intrinsic Point Defects.

Modulation of Vacancy Defects and Texture for High Performance N-Type Bi2 Te3 Via High Energy Refinement.

Development of Nanostructured Bi2Te3 with High Thermoelectric Performance by Scalable Synthesis and Microstructure Manipulations

Functionally Separated Electronic Band Engineering Via Multi-Element Doping Plus High-Density Defects Advances Board-Temperature-range Thermoelectric Performance in GeTe

Broadening temperature plateau of high zTs in PbTe doped Bi0·3Sb1·7Te3 through defect carrier regulation and multi-scale phonon scattering

Tailoring Thermoelectric Performance of n-type Bi2Te3 through Defect Engineering and Conduction Band Convergence