Abstract:Due to the increasing demand for high-power density of electronic devices, the technological enhancement of thermal interface materials (TIMs) is of crucial importance for further advancement of the issue of thermal management. Graphene displayed a huge possibility for the advancement of thermal interface materials because of its extreme, high thermal conductivity. Modest quantities of 2D (two-dimensional) graphene sheets are typically mixed into a polymer matrix to manufacture the nanocomposites with enhanced functional or mechanical properties. A simplistic and useful method to bond a few-layer graphite (AFLG) and AgNWs with polydimethylsiloxane (PDMS), print on the high thermal conductivity three-dimensional (3D) structure fiber with different ratios of Cu powder, the corresponding composite with the improvement of thermal conductivity is made. The thermal conductivity of composites with 20 wt% AFLG and AgNWs at 2.0 mg/mL displays an increase when the Cu particles loading of 2.5 to 7.5 wt% adding. The effect is attributed to the intercalation of spherical copper particles between other fillers that come out of the formation of the percolation network with high thermal conductivity. Thermal conductivity of through-plane (KZ) 5.96 W/mK and in-plane (Kx) 41.7 W/mK are achieved in composites with 7.5 wt% copper particle loading. Consequently, the process in this study endows these nanocomposites with high thermal conductivity. Besides, the proposed nanostructure-tailored nanocomposites are promising for surface variations with time during heating and cooling. The results brightly show the interaction between the Cu particles and above fillers in the nanocomposites and demonstrate the potential of the hybrid nanocomposites in the field of TIMs for practical applications. The novelty and contribution of this study integrate the comprehensive benefits of AgNWs, Cu, and PDMS that lie in the low-cost fabrication method via the interconnection of 1D/2D/3D nanostructures based on hybrid supported fillers for enhanced thermal interface to fabricated thermal interface materials with new architectures. The ball-milled-structured Cu powder is added to 2D-structured AFLG and enhanced the in-plane thermal conductivity by about 2 times. The through-plane thermal conductivity was enhanced by about 1.18 times. The multiple fillers structure not only brings the process easier to achieve but is also environmentally friendly in the era of a highly polluted world.

A zero-thermal-expansion composite with enhanced thermal and electrical conductivities resulting from 3D interpenetrating copper network

Fabrication of Three-dimensional Thermally Conductive Carbon Fibers/Carbon Nanotubes Network Reinforce Epoxy Composites

Zero thermal expansion, high specific thermal conductivity, and good machinability of Cu2P2O7/2024Al composite

Superior overall performance of zero thermal expansion ZrW2O8/Al–Si composite

High thermal and mechanical properties of carbon fiber network reinforced copper matrix composites achieved by configuration design and interface engineering

Vertically Interconnected Structure Enhances the Thermal Management Capability of Copper-Based Composites

Microstructure and thermal properties of copper matrix composites reinforced by 3D carbon fiber networks

Improving electromagnetic engineering of thermal conductive composites by establishing continuous thermal conductive networks with gradient impedance

Ultrahigh thermal conductive polymer composites by the 3D printing induced vertical alignment of carbon fiber

Sintering pressure effect on the performances of near-zero thermal expansion xLFCS/Cu metal matrix composites

High thermal conductivity of epoxy composites via micro-zone enhanced 3D interconnected nickel skeleton

Quasi-Hyperbolic Framework Graphite Foam-Based Composites with High Thermal Conductivity and Electromagnetic Shielding Properties Fabricated by an Electrochemical Expansion Method

Design of near-zero thermal expansion composites with superior mechanical properties in a wide temperature region

Near-zero thermal expansion of ZrW2O8/Al–Si composites with three dimensional interpenetrating network structure

Thermally Conductive Polydimethylsiloxane-Based Composite with a Three-Dimensional Vertically Aligned Thermal Network Incorporating Hexagonal Boron Nitride Nanosheets and Nanodiamonds

Research status of thermal conductivity in copper-carbon composite materials

Fabrication of copper powder hybrid supported fillers with interconnected 1D/2D/3D nanostructures for enhanced thermal interface materials properties

Epoxy/ copper-nickel metal foam composites with high thermal conductivity using an electroplating method

Highly enhanced stability and thermoelectric performance of copper sulfides-based composites by multiphase engineering

Effects of Zr-Cu Alloy Powder on Microstructure and Properties of Cu Matrix Composite with Highly-Aligned Flake Graphite

Synergistic Effect of Aligned Graphene Nanosheets in Graphene Foam for High‐Performance Thermally Conductive Composites