Abstract:Solid-state lithium (Li) metal batteries are widely used due to their excellent safety, superior energy density, and low cost. Nevertheless, the practical application of solid-state Li batteries is hindered by the inferior ionic conductivity of the solid electrolyte and poor interface contact between the electrode and electrolyte. Herein, a flexible, hybrid ceramic-based electrolyte was fabricated by a solution-casting method using poly(vinylidene fluoride), Li1.4Al0.4Ti1.6(PO4)3 powders, and lithium bis(trifluoromethanesulfonyl)imide. To realize high ionic conductivity and a stable self-viscous electrode/electrolyte interfacial contact simultaneously, a mixed solution of 1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide, lithium bis(trifluoromethanesulfonyl)imide, and fluoroethylene carbonate was introduced by the solution-infiltration method. The self-viscous Li1.4Al0.4Ti1.6(PO4)3 ceramic-based electrolyte exhibits superior ionic conductivity (2.4 × 10–4 S cm–1 at 25 °C), a high ionic transference number (0.42), wide voltage window (4.8 V vs Li/Li+), excellent thermal stabilities, and the ability to impede Li dendrite growth. In particular, the stable contact, low interfacial resistance, and fast ion-transport channels between the electrodes and solid electrolytes can be achieved by the self-viscous interfacial layer. The solid-state LiFePO4|Li battery assembled with the solid self-viscous electrolyte demonstrates a satisfactory initial discharge capacity of 138.0 mAh g–1 and capacity retention of 96.5% after 200 cycles at 0.5 C and under 25 °C. The self-viscous modification strategy of the solid electrolyte affords promising options for implementing the intimate electrode/electrolyte interfacial contact in high-energy-density solid-state batteries.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acs.energyfuels.1c01202.Figure S1: XRD patterns and SEM image of LATP ceramic powders. Figure S2: Temperature dependence of ionic conductivities for LATP pellets. Figure S3: Flexible and winding performances of self-viscous PLL-LEF electrolyte. Figure S4: Surface morphology of PL and PLL-LEF electrolytes. Figure S5: Adhesiveness exhibitions of PLL-LE composite electrolyte. Figure S6: EIS profiles of 10LiTFSI-40EMITFSI and 10LiTFSI-40EMITFSI-10FEC electrolytes. Figure S7: EIS profiles of stainless steel|PLL-LEF|Li cells. Figure S8: Thermogravimetry curve of PLL-LEF electrolyte. Figure S9: Flammability test of routine Celgard separator. Figure S10: EIS profiles of Li|PLL|Li cell for different aging times. Figure S11: Optical photographs of the PLL electrolyte. Figure S12: Ti 2p XPS of the PLL electrolyte. Figure S13: EIS profiles of Li symmetric cell with different electrolytes after cycling. Figure S14: Constant current cycling curves of Li|PLL-LEF|Li cells at 0.2 mA·cm–2. Figure S15: Constant current cycling curves of Li|PLL-LEF|Li cells at 0.5 mA·cm–2. Figure S16: Constant current cycling curves of Li|PLL-LEF|Li cells. Figure S17: High multiple SEM images of Li surfaces obtained from Li symmetrical cells. Figure S18: SEM image of pristine Li surface. Figure S19: EIS results of LiFePO4|PLL|Li, LiFePO4|PLL-LE|Li and LiFePO4|PLL-LEF|Li batteries. Figure S20: Typical charge–discharge voltage profiles of LiFePO4|PLL-LE|Li cell at 0.5 C. Figure S21: Electrochemical properties of Al2O3@LiNi0.5Co0.3Mn0.3O2|PLL-LEF|Li cell (PDF)This article has not yet been cited by other publications.

Covalent Organic Frameworks Interfacial Modification of Ceramic Electrolytes for Enhanced Electrochemical Performance

Covalent Organic Framework Enhanced Solid Polymer Electrolyte for Lithium Metal Batteries

Complementary Hybrid Design of Solvated Electrolyte Membranes Enabled by Porous Carbon Reinforcement for High-Performance Lithium Batteries

In Situ Gelation of a 1,3-Dioxolane Dual-Permeable Porous Tandem Framework with Excellent Interfacial Stability to Power Long-Cycling Solid-State Lithium Metal Batteries

Fabrication of Scalable Covalent Organic Framework Membrane-based Electrolytes for Solid-State Lithium Metal Batteries

Dual-Salt-Containing Polymer Interlayer Stabilizes Solid-State Li-Metal Batteries with LiCoO 2 Cathodes

Cellulose Mesh Supported Ultrathin Ceramic-Based Composite Electrolyte for High-Performance Li Metal Batteries

Lithium-ion transport in covalent organic framework membrane

In-situ constructing of dual bifunctional interfacial layers of garnet-type Li6.4La3Zr1.4Ta0.6O12 solid electrolyte towards long-cycle stability for flexible solid metal lithium batteries

Nano-Structured Li1.3al0.3ti1.7(Po4)3 Coated Licoo2 Enabling Compatible Interface with Ultrathin Garnet-Based Solid Electrolyte for Stable Li Metal Battery

Flexible solid-state electrolyte based on comb-like PEG-functionalized covalent organic frameworks for lithium metal batteries

Enhanced Interphase Ion Transport via Charge‐Rich Space Charge Layers for Ultra‐Stable Solid‐State Lithium Metal Batteries

Anionic covalent organic framework electrolyte with tailored ion channels for high-areal-capacity solid-state lithium metal battery

Tailoring of Li/LATP-PEO Interface via a Functional Organic Layer for High-Performance Solid Lithium Metal Batteries

Constructing Robust LiF‐Enriched Interfaces in High‐Voltage Solid‐State Lithium Batteries Utilizing Tailored Oriented Ceramic Fiber Electrolytes

In Situ Constructing Ultrathin, Robust‐Flexible Polymeric Electrolytes with Rapid Interfacial Ion Transport in Lithium Metal Batteries

Stabilizing Ceramic-Based Electrolyte Interfaces with Self-Viscous Modification Strategy for Solid-State Lithium Batteries

Flexible ion-conducting membranes with 3D continuous nanohybrid networks for high-performance solid-state metallic lithium batteries

In Situ Constructing Robust Interface by Deep Eutectic Polymeric Electrolyte Enables High Performance Lithium Metal Batteries with High‐Loading Cathode

In Situ Construction of Ether-Based Composite Electrolyte with Stable Electrode Interphase for High-Performance Solid State Lithium Metal Battery

Modification of Solid Electrolyte Interface Layer Between PVDF-based Electrolyte and Lithium Anode