Formation Mechanism of Monocyclic Aromatic Hydrocarbons during Pyrolysis of Styrene Butadiene Rubber in Waste Passenger Car Tires

Jiayuan Li,Dahai Zheng,Zihao Yao,Shixin Wang,Ruinian Xu,Shengwei Deng,Biaohua Chen,Jianguo Wang

DOI: https://doi.org/10.1021/acsomega.2c04994

IF: 4.1

2022-12-06

ACS Omega

Abstract:ACS Omega . 2022 Nov 16;7(47):42890-42900. doi: 10.1021/acsomega.2c04994. eCollection 2022 Nov 29. NO

chemistry, multidisciplinary

What problem does this paper attempt to address?

Molecular Dynamics Simulation of PAHs Generated from Rubber Pyrolysis

Zhengcheng Wen,Mingrui Chang,Jing Guo

DOI: https://doi.org/10.1080/10406638.2024.2408460

2024-10-02

Polycyclic Aromatic Compounds

Abstract:The rapid expansion of the automotive industry has posed challenges for the waster tire rubber sector. Pyrolysis, as a prominent method for waster rubber treatment, inevitably produces polycyclic aromatic hydrocarbons (PAHs), which serve as precursors to dioxins and exhibit high toxicity. This study utilizes molecular dynamics simulations to investigate the thermal decomposition of rubber macromolecules and the subsequent formation of PAHs. Initially, an overall simulation of the pyrolysis process is conducted to analyze the evolution of pyrolysis products. The pyrolysis of rubber involves sequential decomposition and polymerization, with the evolutionary analysis of the decomposition products with various numbers of carbon atoms used to validate this process. Subsequently, the factors influencing PAH formation are examined and assessed. Temperature elevation enhances rubber pyrolysis, while the maturity of PAH molecules is linked to oxygen levels. The introduction of hydrogen or hydroxyl groups can partially impede PAH generation. This investigation elucidates the mechanisms governing PAH generation during rubber pyrolysis, with the goal of aiding in the effective regulation of PAHs in waster rubber pyrolysis.

chemistry, organic
Formation Behavior of PAHs During Pyrolysis of Waste Tires.

Wenwen Ye,Xu,Mingxiu Zhan,Qunxing Huang,Xiaodong Li,Wentao Jiao,Yongguang Yin

DOI: https://doi.org/10.1016/j.jhazmat.2022.128997

IF: 13.6

2022-01-01

Journal of Hazardous Materials

Abstract:Polycyclic aromatic hydrocarbons (PAHs) formation from the pyrolysis of waste tires is inevitable because of the complexity of tire formulations and the addition of certain chemicals. In this study, the formation behavior and distribution of PAHs in three-phases were investigated from waste tires under pyrolysis conditions. The influencing factors including the temperature, heating rate, holding time, particle size, catalyzer, and atmosphere, were systematically evaluated. The results showed that PAHs were mainly concentrated in pyrolysis oil (94.59-99.03%), followed by the gas phase (0.96-5.34%), and their content was very low in the solid phase (0.01-0.99%). A higher temperature and slower heating rate lead to partial PAHs decomposition, thus reducing their emissions. The overall formation of PAHs can be inhibited when pyrolyzing coarse-grained tire powder. Furthermore, the PAHs formation mechanisms in waste tires were determined through reaction molecular dynamics, electron paramagnetic resonance, and intermediate products. Tires were mainly decomposed into benzene series, *C2H3, and *CH3; therefore, it was determined that PAHs were formed by the joint action of the hydrogen abstraction, and vinyl radical addition and methyl addition cyclization mechanisms. Among them, low and middle-ring PAHs were formed more easily, particularly naphthalene. The generation of PAHs can be inhibited by reducing the concentration of hydrocarbons and monocyclic benzene series. Regarding the distribution law and generation pathways of PAHs, our results provide guidance for reducing PAHs formation and emissions.
Mechanism analysis of gas products from catalytic pyrolysis of tire rubber based on reaction thermodynamics and kinetics

Shuangpeng Yu,Qirong Yang,Zhaoying Li,Ting Liu,Li Tao,Erren Yao,Yuan Zhang

DOI: https://doi.org/10.1016/j.fuproc.2021.107134

IF: 8.129

2022-03-01

Fuel Processing Technology

Abstract:In this paper, the gas products from pyrolysis of tire rubber was respectively studied by fixed bed pyrolysis experiments—gas chromatography analysis and molecular dynamics simulations. The results of experiments showed that the main gas products of pyrolysis were CH4, H2, and C2H4. The simulation results showed that the long rubber chain broke into four main rubber monomers at low temperature: isoprene, styrene, 1,3-butadiene and uncondensated C4H6·. And at higher temperature, the generated monomers were pyrolyzed into small molecule gases. Fe2O3 reduced the final pyrolysis temperature and increased the pyrolysis rate with a good catalytic reactively. And it changed the gas products distribution, in which the proportion of CH4 and H2 were promoted while the proportion of C2H4 was reduced. In order to obtain the thermodynamic and kinetic data of each reaction path, DFT calculation was carried out. The reaction paths of three major radicals H·, CH3·, and CH2 = CH· were further discussed. The results showed that Fe2O3(commercial) promoted the release of CH3· from isoprene monomer and CH3· attack on isoprene monomer and 1,3-butadiene to produce CH4. Moreover, Fe2O3 promoted H· attacking styrene monomer to generate H2.

energy & fuels,engineering, chemical,chemistry, applied
Molecular Dynamics Simulation of Waste Tire Pyrolysis at High Temperature

Zhengcheng Wen,Jing Guo,Yuan Li,Qunxing Huang

DOI: https://doi.org/10.1007/s41742-023-00531-z

2023-04-20

International Journal of Environmental Research

Abstract:Pyrolysis is one of the most promising methods to treat waste tires. In this paper, a waste rubber model is established, and the pyrolysis process of rubber polymer at 1500–3000 k is investigated by molecular dynamics simulation. The whole pyrolysis process, the pyrolysis behavior of each component and the formation of S and N compounds are studied in detail. The results show that natural rubber (NR), styrene butadiene rubber (SBR) and nitrile rubber (NBR) are in the leading position in the pyrolysis process. When the carbon chain of rubber macromolecule breaks, many C and H atoms escape from it and combine with each other to form CH 3 , H radicals, CH 4 , H 2 , etc.; The pyrolysis products of waste rubber mainly include hydrocarbons CH 4 , C 2 H 2 , C 4 H 2 , C 5 H 4 , sulfur compounds H 2 S, CH 3 SH, HS, nitrogen compounds NH 3 , HCN and small molecule substances H 2 ; The increase of temperature can promote the pyrolysis of rubber, promote the carbon chain fracture, and promote the formation of more H 2 S; For H 2 S formation, HS is an important intermediate. HS compounds are mainly formed through the gradual pyrolysis of thiophene and polysulfide rubber. HS is stabilized by the transfer of H atoms. For nitrogenous pollutants, HCN is an important component in the pyrolysis. With the increase of temperature, the amount of HCN increases because of the decomposition of complex nitrogen compounds. The amount of oxygen has little effect on sulfide and nitride. At high temperature, nitrogen will also participate in the pyrolysis reaction. This paper reveals the pyrolysis behavior of waste rubber and the formation mechanism of S and N pollutants through simulation research, which provides a reference for the further development of waste tire rubber pyrolysis recovery.

environmental sciences
Carbon Black Production Characteristics and Mechanisms from Pyrolysis of Rubbers: Insights from Experiments and Reaxff Molecular Dynamics Simulations

Hao Jiang,Qiang Hu,Jingai Shao,Youjian Zhu,Wei Cheng,Junjie Zhang,Tingting Fan,Jie Yu,Haiping Yang,Xiong Zhang,Hanping Chen

DOI: https://doi.org/10.2139/ssrn.4415589

2023-01-01

Abstract:Pyrolysis is a clean and low-carbon treatment strategy for waste tires. It provides a promising and sustainable alternative approach for carbon black production by waste tire volatile polymerization at high temperatures. However, the complex decomposition and repolymerization processes from different rubber fractions in waste tires led to the carbon black formation mechanisms still unclear. Here, the volatile polymerization behavior, the yield, morphology, particle diameter and chemical structure evolution of carbon black during natural rubber (NR), butadiene rubber (BR), and styrene-butadiene rubber (SBR) pyrolysis at 1100-1300 °C were investigated. Carbon black yield increased from 20.8%-24.4% to 47.9%-56.7% from 1100 to 1300 °C. The yield from NR was 4.1% and 8.8% lower than that of BR and SBR at 1300 °C. While the graphitization degree (ID/IG=2.22), microcrystal length (3.17 nm) and mean particle diameter (90.3 nm) from NR were the highest. Volatile evolution, carbon black nucleation mechanisms were revealed by reactive force-field molecular dynamics simulation. C-addition-H-migration and radical-chain reactions contributed to cyclic molecule formation, which was then converted to carbon black via C-C coupling and graphitization. NR decomposed into more C3H5·, C3H4·, CH3· and CH4, while BR and SBR generated more C2H2, C2H3·, long carbon-chains and cyclic molecules, which resulted in higher carbon black yield from BR and SBR than NR. With few defect borders and regular stacking and wrapping of aromatic layers, carbon black from NR exhibited more ordered nucleation and high graphitization degree. This study can help optimize the screening of rubber fractions in waste tires to achieve carbon black selective production.
Rubber Pyrolysis: Kinetic Modeling and Vulcanization Effects

Sheng Liu,Jie Yu,Kagiso Bikane,Tao Chen,Chuan Ma,Ben Wang,Lushi Sun

DOI: https://doi.org/10.1016/j.energy.2018.04.146

IF: 9

2018-01-01

Energy

Abstract:Kinetic studies and the effect of the vulcanization process on the pyrolysis of natural rubber (NR), butadiene rubber (BR) and styrene-butadiene rubber (SBR) were investigated in this work. A comprehensive kinetic study using a model-based method, a model-free method and the distribution activation energy model (DAEM) was applied and a comparison between the different models was drawn. The DAEM showed a better fitting of the experimental results than the model-based method. The activation energy distribution of the DAEM verified by the model-free method indicated that the main decomposition of rubbers followed a chain reaction mechanism. Pyrolysis of raw rubbers and their corresponding vulcanized rubbers were conducted in a fixed-bed reactor. The sulfur content and product yields were quantified. Pyrolysis oils were characterized and compared. The oil yields reached a maximum at 430 degrees C for NR (90.82%), 470 degrees C for both BR (90.61%) and SBR (92.80%). Pyrolytic oils of raw rubbers were mainly composed of their corresponding monomer or dimer, trimer compounds. However, the results of vulcanized rubbers pyrolysis were significantly different. Sulfur in the vulcanized rubbers was released at low temperatures due to the lower bond energy. Higher temperatures led to the conversion of sulfur-containing oils to gaseous compounds. Vulcanization promoted the decomposition of rubbers at low temperatures but had an insignificant influence on pyrolysis products distribution at high temperature. Pyrolysis oils of vulcanized rubbers were more complex, constituting various aromatic hydrocarbons and thiophenes. (C) 2018 Elsevier Ltd. All rights reserved.
Carbon black production characteristics and mechanisms from pyrolysis of rubbers

Hao Jiang,Jing’ai Shao,Qiang Hu,Youjian Zhu,Wei Cheng,Junjie Zhang,Tingting Fan,Jie Yu,Haiping Yang,Xiong Zhang,Hanping Chen

DOI: https://doi.org/10.1016/j.fuproc.2023.108011

IF: 8.129

2023-12-15

Fuel Processing Technology

Abstract:Pyrolysis is a promising way to treat the waste tires for high value carbon black production. However, the carbon black formation mechanism is still unclear due to the complex decomposition and polymerization reactions during the pyrolysis of tire components. In this study, the production behavior, characters, and mechanism of carbon black from pyrolysis of natural rubber (NR), butadiene rubber (BR), and styrene-butadiene rubber (SBR) were investigated. The yield of carbon black was increased from 20.8%–24.4% to 47.9%–56.7% with the increase of pyrolysis temperature from 1100 to 1300°C. Although the carbon black production yield from NR was lower than that of BR and SBR at 1300°C, the graphitization degree ( I D / I G = 2.22), microcrystal length (3.17 nm) and mean particle diameter (90.3 nm) of the carbon black derived from NR were the highest. The volatile evolution, carbon black nucleation mechanisms were revealed by reactive force-field molecular dynamics simulations. The pyrolysis of BR and SBR generated more C 2 H 2 , C 2 H 3 ⋅, long carbon-chains and cyclic molecules than NR, which probably resulted in a higher carbon black yield than NR. With few defect borders, regular stacking and wrapping of the aromatic layers, the carbon black from NR exhibited more ordered nucleation and high graphitization degree.

energy & fuels,engineering, chemical,chemistry, applied
Molecular dynamics study of waste tire pyrolysis: Focus on intermediate product evolution and sulfur migration law

Jingwei Qi,Yijie Wang,Pengcheng Xu,Ming Hu,Taoli Huhe,Xiang Ling,Haoran Yuan,Jiadong Li,Yong Chen

DOI: https://doi.org/10.1016/j.jece.2024.114633

IF: 7.7

2024-11-07

Journal of Environmental Chemical Engineering

Abstract:With the rapid development of the automotive industry, the large number of waste tires poses significant environmental and health pressures. Pyrolysis technology offers a way to resourcefully utilize waste tires by converting them into pyrolysis oil, pyrolysis gas, and pyrolysis char, which has promising application prospects. However, there are still considerable challenges in the application of this technology, such as unclear reaction mechanisms and the high sulfur content of the products, which limit its practical implementation. Although some research has elucidated the pyrolysis mechanisms, there remain significant gaps in understanding the evolution paths of key intermediate and final products, as well as the detailed migration and transformation patterns of sulfur. This study uses reactive molecular dynamics simulation to investigate the pyrolysis process of tires. A three-dimensional polymer molecular model was constructed to study the pyrolysis process of waste tires at different temperatures, focusing on the evolution of key products, intermediate products, and sulfur-containing components. The results indicate that CH 4 and ·CH 3 radicals collide with unsaturated hydrocarbons through carbon-hydrogen transfer reactions and radical chain reactions, leading to polymerization. During the initial stage of pyrolysis, sulfur primarily exists in the form of sulfur-containing hydrocarbons (CHS). As pyrolysis progresses, the quantity of CHS decreases. With increasing pyrolysis temperature, the proportion of sulfur in the S form far exceeds that of CHS. At a pyrolysis temperature of 3000 K, the proportion of S is 64 %, while the proportion of CHS is 23 %.

engineering, chemical, environmental
Interaction during co-pyrolysis of different rubbers using rapid infrared-heating fixed bed: products distribution, tar quality and tar composition

Yuxin Wen,Zhixian Bao,Zhengzheng Liu,Dekang Li,Haoquan Hu,Lijun Jin

DOI: https://doi.org/10.1016/j.fuel.2024.131065

IF: 7.4

2024-02-03

Fuel

Abstract:Pyrolysis of waste tire (WT) is an efficient method to convert it into fuels and high-value chemicals. However, the main organic components of tire including natural rubber (NR), styrene butadiene rubber (SBR) and butadiene rubber (BR) usually exert interaction during pyrolysis. To investigate the interactions between different rubbers, individual pyrolysis and co-pyrolysis of three pure rubbers were conducted using an infrared-heating fixed-bed reactor, and the synergy during co-pyrolysis was revealed based on products distribution, tar quality and compositions from pyrolysis of pure rubber and waste tire. The results show that tar yields from rubber pyrolysis exceed 90 wt% and tar compositions are related to the molecular structures of rubbers. Co-pyrolysis between different rubbers promotes gases formation and inhibits char formation. The interaction between NR and SBR facilitates the formation of cycloolefin and chain olefin, but co-pyrolysis of SBR and BR contributes to the aromatic hydrocarbons formation. Similar tar components from pyrolysis of demineralized waste tire as those from pyrolysis of NR/SBR/BR sample indicate that waste tire pyrolysis contains individual pyrolysis and co-pyrolysis of different rubbers. The potential reaction process of WT was also proposed. The insight on interaction between different rubbers will provide a good guide for efficient pyrolysis of waste tire.

energy & fuels,engineering, chemical
Pyrolysis of vulcanized styrene-butadiene rubber via ReaxFF molecular dynamics simulation

Yinbin Wang,Senjun Yao,Wei Wang,Chenglong Qiu,Jing Zhang,Shengwei Deng,Hong Dong,Chuan Wu,Jianguo Wang

DOI: https://doi.org/10.1016/j.cjche.2020.10.033

IF: 3.8

2021-03-01

Chinese Journal of Chemical Engineering

Abstract:Cross-linked Styrene-butadiene rubber is modeled in molecular simulation.Sulfur as an agent would promote the crack of polymer chain.High temperature promotes sulfur transformation into H2S as products.At low sulfur content system, hydrocarbon sulfide is the main sulfur products.The elemental sulfur intermediate is observed at high sulfur content systems.Styrene-butadiene rubber (SBR) is widely used in tires in the automotive segment and vulcanization using sulfur is a common process to enhance its mechanical properties. However, the addition of sulfur as the cross-linking agent usually results in impurities in pyrolysis products during rubber recycling, and thus the desulfurization during tire pyrolysis attracts much attention. In this work, the pyrolysis of vulcanized SBR is studied in detail with the help of ReaxFF molecular dynamics simulation. A series of cross-linked SBR models were built with different sulfur contents and densities. The following ReaxFF MD simulations were performed to show products distributions at different pyrolysis conditions. The simulation results show that sulfur products distribution is mainly controlled by sulfur contents and temperatures. The reaction mechanism is proposed based on the analysis of sulfur products conversion pathway, where most sulfur atoms are bonded with hydrocarbon radicals and the rest transfer to H2S. High sulfur contents tend to the formation of elemental sulfur intermediate, and temperature increase facilitates the release of H2S.

engineering, chemical
Evaluation on hydrothermal gasification of styrene-butadiene rubber with oxidants via ReaxFF-MD simulation

S Q Nie,M Q Chen,Q H Li

DOI: https://doi.org/10.1016/j.wasman.2023.08.019

2023-09-01

Abstract:Styrene-butadiene rubber (SBR) is widely used in tires, which brings great challenge to the disposal and reclaiming of the used tires. The ring-opening reaction pathways of benzene rings in hydrothermal gasification of styrene-butadiene rubber were revealed based on reactive force field molecular dynamics (ReaxFF-MD) simulation. H-abstraction reaction that OH radicals capture H atom from the vinyl group of styrene was critical to the degrading of the styrene monomers. The energy barrier of H2O2 converted to OH radicals was lower than that of O2 and pure water converted to OH radicals. The oxidants that can urge OH radical formed in reaction were beneficial to SBR degradation, which could be assigned to confirm that SBR degradation with H2O2 was better than that with oxygen at the same concentration. The addition of oxidant could be helpful for decreasing the degradation temperature of styrene monomers. At oxidant equivalent ratio (ER) of 0.1, H2 yield at 2500 K lifted after 135 ps and increased by 75% at 500 ps compared with that without oxidants. According to the chemical equilibrium analysis, the optimal ER for H2 was 0.4 between 350 and 600 °C (real temperatures). The results could provide theoretic support and experiment guidance for adding oxidants in reclaiming waste rubber products.
Soybean Oil Induced Efficient Thermal-Oxidative Degradation of Covalently Crosslinked Styrene Butadiene Rubber

Zhen Zhang,Chaoying Wan,Pan Song,Yanling Xie,Yuxin Zhang,Shifeng Wang

DOI: https://doi.org/10.1002/app.48935

IF: 3

2020-01-01

Journal of Applied Polymer Science

Abstract:It has been a technical challenge of recycling tire rubbers due to the covalently crosslinked polymer network structure. Unlike conventional recombination of crosslinked SBR under thermal oxidation, SBR vulcanizate was efficiently degraded by thermal oxidation at 150 degrees C in presence of soybean oil, resulting in 47.3% sol fraction by weight. The structural evolution of SBR vulcanizates during thermal oxidation was characterized by sol-gel ratio, chemical structure, molecular weight, and oxidative erosion on the rubber surface. It was found that the continuous oxidation process facilitated main chain scission of SBR vulcanizates, resulting in a decrease of molecular weight of the sol fraction. The concentration of carbonyl groups, sol fraction, and surface erosion continually increased with reaction time. The large amounts of soybean oil significantly affect the thermal stability of SBR vulcanizates. Moreover, soybean oil is more efficient in decomposition of the SBR vulcanizates and results in more homogeneous and efficient oxidation reactions than paraffin oil. (c) 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020, 137, 48935.
Catalytic Pyrolysis of Waste Tire to Produce Valuable Aromatic Hydrocarbons: an Analytical Py-GC/MS Study

Kuan Ding,Zhaoping Zhong,Bo Zhang,Jia Wang,Addy Min,Roger Ruan

DOI: https://doi.org/10.1016/j.jaap.2016.10.023

IF: 6

2016-01-01

Journal of Analytical and Applied Pyrolysis

Abstract:Pyrolysis of waste tire with HY, HZSM-5 (HZ) and purified attapulgite (PA) catalysts to produce valuable aromatic hydrocarbons has been carried out in a Pyrolyzer- Gas Chromatograph/Mass Spectrum (Py-GC/MS) reactor. Likewise, D-limonene and polybutadiene rubber (BR), which played important roles in the pyrolysis process of waste tire, has also been pyrolyzed in the Py-GC/MS reactor with these catalysts. Based on the product distribution, the catalytic pyrolysis mechanisms of D-limonene were proposed, while those of BR were extended. With these mechanisms, the catalytic pyrolysis characteristics of waste tire could be explained reasonably. Results showed that HY promoted a dramatic increase of aromatics from pyrolysis of D-limonene and BR, leading to the considerable growth of aromatics in the degraded products of waste tire. The shape selectivity of HZ to mono-cyclic aromatics performed effectively in the pyrolysis of BR, yet it exhibited a weak performance in the pyrolysis of D-limonene. As a result, upon the catalytic pyrolysis of waste tire, HZ was inferior to HY in the aromatization ability. However, the selectivity of HZ to BTXE (benzene, toluene, xylene and ethylbenzene) was superior to that of HY. PA performed a weaker catalytic ability in promoting the production of aromatics during the pyrolysis of D-limonene, BR and waste tire. (C) 2016 Published by Elsevier B.V.
Effect of Heating Rates on the Fate of Sulfur During Waste Tire Pyrolysis

Boyu Qu,Chuanqun Liu,Yulin Zhang,Zegang Fu,Ye Shui Zhang,Aimin Li,Guozhao Ji

DOI: https://doi.org/10.1016/j.cej.2023.145736

IF: 15.1

2023-01-01

Chemical Engineering Journal

Abstract:The sulfur migration and transformation during waste tire (WT) fast pyrolysis is one of the important influencing factors on the properties of the product. However, WT's thermal history in the previous literature was out of the scope of most actual industrial reactors. To better guide the actual pyrolysis process, the influence of the heating rate on the fate of sulfur in the WT pyrolysis process was investigated by employing a wire mesh reactor. The results showed significantly increasing the heating rate promoted the sulfur migration into volatiles, which indicated WT fast pyrolysis could result in the risk to the environment and the economic value of products. The organic-S was converted to inorganic-S under the effect of ZnO. center dot C4H6 center dot and center dot C5H8 center dot, which were the monomers of natural rubber and butadiene rubber respectively, could combine with sulfur radicals to generate thiophene. Severe secondary reactions occurred to convert thiophene to aromatized thiophene during WT slow pyrolysis. These findings could provide insightful guidance for minimizing sulfureous volatile formation and emissions.
Gas products generation mechanism during co-pyrolysis of styrene-butadiene rubber and natural rubber

Qirong Yang,Shuangpeng Yu,Haowen Zhong,Ting Liu,Erren Yao,Yuan Zhang,Hansen Zou,Wei Du

DOI: https://doi.org/10.1016/j.jhazmat.2020.123302

IF: 13.6

2021-01-01

Journal of Hazardous Materials

Abstract:In this study, reaction molecular dynamics were combined with experiments to gain in-depth understanding of the gaseous pyrolysis products generation mechanism and optimal paths during natural rubber (NR), styrene-butadiene rubber (SBR) and mixed rubbers (NR-SBR) for effective recovery of waste rubber. The results show that the pyrolysis temperature of NR increases gradually with SBR addition. The monomers produced during the initial stage of SBR pyrolysis are mainly 1,3-butadiene and styrene, in which the energy barriers of the formed H and CH2=CH in styrene are higher than those in 1,3-butadiene, and during further pyrolysis the main gas products are H2 and CH4. During co-pyrolysis of NR-SBR, the reaction paths show that increasing H2 yield and decreasing CH4 yield take place easily as SBR content rises. By contrast to pyrolysis of NR, the path of generating CH2=CH in SBR is more difficult while that of CH2=CH abstracting H occurred easily, leading to first enhancement in produced CH2=CH2 followed by a decline. Fixed bed experiments and gas chromatography (GC) analysis identify the main gas products of the three rubbers (NR, SBR, NR-SBR)as H2, CH4 and CH2=CH2 and the change of yield caused by the increase of SBR content are consistent with the simulation results.

environmental sciences,engineering, environmental
Thermal Reprocessing and Closed‐Loop Chemical Recycling of Styrene‐Butadiene Rubber Enabled by Exchangeable and Cleavable Acetal Linkages

Ganggang Zhang,Chenru Tian,Haoran Feng,Tianwei Tan,Runguo Wang,Liqun Zhang

DOI: https://doi.org/10.1002/marc.202100887

IF: 5.006

2022-04-29

Macromolecular Rapid Communications

Abstract:Macromolecular Rapid Communications, Accepted Article.

polymer science
Preparation and Properties of Solution Styrene and Butadiene Rubber (SSBR) Using Novel Structure Modifier

LIU Lian,HU Bai-jiu,WANG Pei,MA Chi,LIU Cheng,ZHANG Chun-qing,LI Yang,WANG Xue,LI Wei

DOI: https://doi.org/10.3321/j.issn:1003-9015.2008.02.020

2008-01-01

Abstract:The ethyl tetrahydrofury ether(ETE) was used as a novel structural modifier for the preparation of solution styrene and butadiene rubber(SSBR).In a 5 L reactor,the high-vinyl SSBR was synthesized by anionic solution copolymerization of styrene and butadiene with n-butyllithium(n-BuLi) as initiator and cyclohexane and n-hexane as mixed solvent.The effects of modifier dosage and polymerization temperature on the kinetics of copolymerization and microstructure of the copolymers were investigated in detail.The conversion of monomers,coupling efficiency and microstructure of the copolymers were analyzed by gas chromatograph(GC),gel permeation chromatograph(GPC) and nuclear magnetic resonance(1H-NMR),respectively.It was found that the copolymerization rate increases with increasing the modifier adding amount,and the 1,2-units of polybutadiene in SSBR could be controlled in the range of 10% to 60% by altering the modifier adding amount or the initiation temperature.At 50℃ and using tin tetrachloride(SnCl4) as coupling agent,the coupling efficiency could be maintained at more than 60%.The synthesized SSBR possesses good physical and mechanical properties and excellent wet skidding-resistance performance,and thus the synthetic product is a potential matrix for race tire treads and rain tire treads.
Effect of styrene butadiene rubber on the light pyrolysis of the natural rubber

Pan Song,Xiaoyu Wu,Shifeng Wang

DOI: https://doi.org/10.1016/j.polymdegradstab.2017.12.006

IF: 5.204

2018-01-01

Polymer Degradation and Stability

Abstract:The use of styrene butadiene rubber (SBR) in tire rubber presents a challenge for the recycling of tire rubber because of its complex degradation behavior compared with that of natural rubber (NR). The effect of the composition of SBR on the degradation of NR was observed by light pyrolysis at variable times at 300 °C. The morphology, sol-gel evolution of the NR/SBR blends and the degradation mechanism was investigated. In addition, the structural evolution of the sol and gel fractions were measured by Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA). The results indicated that the mechanism of degradation between SBR and NR differed significantly at 300 °C. The broken molecular chains present in SBR recombined with themselves or those of NR to form a new crosslinked network. The results also showed that the ratio of NR/SBR in the sol and gel fractions remains almost constant and unrelated to the original ratio of the NR/SBR blends. Following an increase in SBR content, the sol fraction of different NR/SBR blends mainly consisted of the small molecular chains of NR, whereas the gel fraction mostly constituted re-crosslinked SBR molecular chains.
Formation mechanism of hydrogen production from catalytic pyrolysis of waste tires: A ReaxFF molecular dynamics and experimental study

Zhaoying Li,Qirong Yang,Li Tao,Xinru Ma,Jie Zhou,Tao Ye,Jinhu Wu,Ronghua Wu,Haoxi Ben

DOI: https://doi.org/10.1016/j.fuel.2023.127664

IF: 7.4

2023-02-11

Fuel

Abstract:The mechanism for the formation of gaseous products, especially hydrogen, from the catalytic pyrolysis of waste tires by using Ni-based catalysts has been studied. The catalytic pyrolysis of the three essential components of waste tires such as natural rubber (NR), styrene-butadiene rubber (SBR), and cis -polybutadiene rubber (BR) was simulated and the pyrolysis fracture of the molecular chain was investigated. This work aims to provide a deeper understanding of the reaction thermodynamics and kinetics for the formation mechanisms of gaseous products, primarily hydrogen. Microwave-assisted catalytic pyrolysis of the waste tires over Ni-based catalysts was carried out and used to assent to the simulation results. The study revealed that with the incorporation of 10 wt% Ni/ZSM-5 catalyst, the relative content of H 2 from the catalytic pyrolysis of waste tires can be significantly improved by about 41.3 % in comparison to the same measurement done in the absence of the catalyst. Kinetic and thermodynamic simulations for the catalytic pyrolysis of waste tires were also performed and the corresponding energy barriers and Gibbs free energy changes were calculated. Accordingly, the optimal reaction path for the hydrogen production was determined by comparing and analyzing the values of those parameters. It was confirmed that the addition of Ni, ZSM-5, and Ni/ZSM-5 catalysts promote the hydrogen production reaction pathways. Among those catalysts, the simulation result verified that Ni/ZSM-5 brings a pronounced hydrogen production capacity, which was consistent with the experimental findings.

energy & fuels,engineering, chemical
Pyrolysis-catalysis of Waste Tire to Enhance the Aromatics Selectivity Via Metal Modified ZSM-5 Catalysts

Boyu Qu,Ye Shui Zhang,Tian Wang,Hang Seok Choi,Yutao Zhang,Zegang Fu,Aimin Li,Guozhao Ji

DOI: https://doi.org/10.1016/j.psep.2024.07.041

IF: 7.8

2024-01-01

Process Safety and Environmental Protection

Abstract:Excessive untreated waste tires (WT) have posed threats to the environment and human health. Pyrolysis-catalysis, as a promising treatment technology, could convert WT into high-valued products such as pyrolysis oil. Moreover, BTX compounds (Benzene, toluene, and xylene) were important raw materials in the chemical industry. In order to sharply increase the BTX selectivity in the pyrolytic oil, transition metals (Ni and Fe) were impregnated on the ZSM-5 catalyst. Furthermore, this paper also explored the effect of catalysis modes, catalysts-to-feedstock mass ratios, and catalysis temperatures on the distribution of the aromatics in the WT pyrolysis-catalysis oil. The results suggested that the optimal operating parameters for BTX compound production with a selectivity of 39.87% were in-situ mode, catalysis temperature=600 degrees C, and catalyst-to-feedstock mass ratio=1:1 by applying Ni/ZSM-5. According to the GC-MS identification results, it proposed that the Diels-Alder reaction of isoprene and cracking and recombination of limonene in the aliphatic hydrocarbon pool were the main paths to generate the aromatics, while the addition of ethylene radicals in the monocyclic aromatic hydrocarbon (MAH) and polycyclic aromatic hydrocarbon (PAH) pools was dominant in the growth of the aromatics. The study provided a viable approach for upgrading WT to produce high-value aromatic products.

Formation Mechanism of Monocyclic Aromatic Hydrocarbons during Pyrolysis of Styrene Butadiene Rubber in Waste Passenger Car Tires

Molecular Dynamics Simulation of PAHs Generated from Rubber Pyrolysis

Formation Behavior of PAHs During Pyrolysis of Waste Tires.

Mechanism analysis of gas products from catalytic pyrolysis of tire rubber based on reaction thermodynamics and kinetics

Molecular Dynamics Simulation of Waste Tire Pyrolysis at High Temperature

Carbon Black Production Characteristics and Mechanisms from Pyrolysis of Rubbers: Insights from Experiments and Reaxff Molecular Dynamics Simulations

Rubber Pyrolysis: Kinetic Modeling and Vulcanization Effects

Carbon black production characteristics and mechanisms from pyrolysis of rubbers

Molecular dynamics study of waste tire pyrolysis: Focus on intermediate product evolution and sulfur migration law

Interaction during co-pyrolysis of different rubbers using rapid infrared-heating fixed bed: products distribution, tar quality and tar composition

Pyrolysis of vulcanized styrene-butadiene rubber via ReaxFF molecular dynamics simulation

Evaluation on hydrothermal gasification of styrene-butadiene rubber with oxidants via ReaxFF-MD simulation

Soybean Oil Induced Efficient Thermal-Oxidative Degradation of Covalently Crosslinked Styrene Butadiene Rubber

Catalytic Pyrolysis of Waste Tire to Produce Valuable Aromatic Hydrocarbons: an Analytical Py-GC/MS Study

Effect of Heating Rates on the Fate of Sulfur During Waste Tire Pyrolysis

Gas products generation mechanism during co-pyrolysis of styrene-butadiene rubber and natural rubber

Thermal Reprocessing and Closed‐Loop Chemical Recycling of Styrene‐Butadiene Rubber Enabled by Exchangeable and Cleavable Acetal Linkages

Preparation and Properties of Solution Styrene and Butadiene Rubber (SSBR) Using Novel Structure Modifier

Effect of styrene butadiene rubber on the light pyrolysis of the natural rubber

Formation mechanism of hydrogen production from catalytic pyrolysis of waste tires: A ReaxFF molecular dynamics and experimental study

Pyrolysis-catalysis of Waste Tire to Enhance the Aromatics Selectivity Via Metal Modified ZSM-5 Catalysts