Abstract:Irreversible phase transition and surface residual lithium, which cause the fast capacity fading of LiNi0.8Co0.1Mn0.1O2 (NCM811), are the main obstacles that hinder their commercial application. Herein, to modify the surface/interphase properties of NCM811, we elaborately propose a hybrid Li3PO4-AlPO4-Al(PO3)(3) coating layer that combines the advantages of ionic conductor (Li3PO4) and thermal stable compound (AlPO4) via reacting aluminum metaphosphate (Al (PO3)(3)) precursor with the surface residual lithium (Li2CO3 or/and LiOH) during the coating process. When used as cathode for lithium-ion battery, the optimized NCM811 delivers a high initial discharge capacity of 201.8 mAh g(-1) and 218.9 mAh g(-1) at 0.1C under the temperature of 30 degrees C and 50 degrees C, with capacity retention of 85.4% and 78.89% after 50 cycles, respectively, which are much higher than that of uncoated sample (73.93% and 57.98%). Moreover, when it is coupled with graphite anode to form a lithium-ion full cell, it delivers an impressively high energy density of 467.5 Wh kg(-1) (based on mass of positive and negative material), and retains 71.8% of its initial energy density after 100 cycles. The significantly enhanced electrochemical properties should be attributed to the multifunctional hybrid nano-coating layer that could efficiently reduce the surface residual lithium, suppress the irreversible phase transition, and prevent the active materials from the erosion of HF as verified by the ex-situ X-ray diffractometry, Raman spectroscopy and transmission electron microscopy. This work provides new insights into the surface/interphase design strategies to improve the structural stability of Ni-rich cathode, which will promote the development of high capacity cathode materials.

Controlled preparation of nano-Al2O3/PPy composite coatings to compensate surface structural defects of lithium-rich layered oxides

Improving electrochemical performance of Ni-rich LiNi0.8Co0.1Mn0.1O2 cathode for Li-ion batteries by dual-conductive coating layer of PPy and LiAlO2

Realizing Superior Cycling Stability of Ni-Rich Layered Cathode by Combination of Grain Boundary Engineering and Surface Coating

Constructing Electronic and Ionic Conductive Double Coating to Achieve Superior Structure Stability and Electrochemical Properties of LiNi0.90Co0.04Mn0.03Al0.03O2

Enhanced Electrochemical Performance of Ni-rich LiNi0.6Co0.2Mn0.2O2 Coated by Molecular Layer Deposition Derived Dual-Functional C-Al2O3 Composite Coating

Face-lifting the Surface of LiNi0.8Co0.15Al0.05O2cathode Via Y(PO3)3to Form Anin Situtriple Composite Li-ion Conductor Coating Layer with the Enhanced Electrochemical Performance.

In-situ Formation of Hybrid Li3PO4-AlPO4-Al(PO3)3 Coating Layer on LiNi0.8Co0.1Mn0.1O2 Cathode with Enhanced Electrochemical Properties for Lithium-Ion Battery

Enhanced interfacial reaction interface stability of Ni-rich cathode materials by fabricating dual-modified layer coating for lithium-ion batteries

Improving the Cycle Stability of LiNiO2 through Al3+ Doping and LiAlO2 Coating

In-situ construction protective layer and phosphate doping synergistically improve the long-term cycle stability of LiNi0.6Co0.1Mn0.3O2

New insights into dry-coating-processed surface engineering enabling structurally and thermally stable high-performance Ni-rich cathode materials for lithium ion batteries

Bulk Mg-doping and Surface Polypyrrole-Coating Enable High-Rate and Long-Life for Ni-rich Layered Cathodes

Double Conductor Coating to Improve the Structural Stability and Electrochemical Performance of LiNi 0.8 Co 0.1 Mn 0.1 O 2 Cathode Material

Superior Electrochemical Properties of Ni-Rich LiNi 0.85 Co 0.05 Mn 0.10 O 2 Cathode with the Stable Polypyrrole Coating and Boron Doping for Li-Ion Batteries

Highly Stable Li1.2mn0.54co0.13ni0.13o2 Enabled By Novel Atomic Layer Deposited Aipo(4) Coating

Surface Coating of NCM523 Cathode Electrodes by the Difunctional Block Copolymer/Lithium Salt Composites

A Highly Homogeneous Nanocoating Strategy for Li-rich Mn-based Layered Oxides Based on Chemical Conversion

Improved Electrochemical Performances of Li- and Mn-Rich Layered Oxides 0.4li4/3mn2/3o2·0.6lini1/3co1/3mn1/3o2 Cathode Material by Co3O4 Coating

Double Conductor Coating to Improve the Structural Stability and Electrochemical Performance of LiNi0.8Co0.1Mn0.1O2 Cathode Material

Chemically converting residual lithium to a composite coating layer to enhance the rate capability and stability of single-crystalline Ni-rich cathodes

Optimized structure stability and cycling performance of LiNi0.8Co0.1Mn0.1O2 through homogeneous nano-thickness Al2O3 coating