Abstract:Modern civilization and cutting-edge technologies and tools are highly dependent on energy storage devices and demand efficient and long-lasting high-energy-density storage devices. Lithium metal batteries have surpassed their competitors concerning energy density due to their inherent high specific capacity (3860 mAh/g) and the lowest electrochemical potential (-3.04 V vs. standard hydrogen electrode), proving to be one of the most favorable energy storage devices for smart and mobile gadgets, electric automobiles, grid storage, etc. However, safety-threatening and performance-decay challenges associated with lithium metal anodes, such as lithium dendrite formation, uncontrolled parasitic reactions between Li-metal and electrolyte, low coulombic efficiency, dead Li-formation, etc., restrict its employment in practical batteries. The root cause of the dendrite formation is poor Li-ion conductivity of bulk lithium metal, which results in an uneven electric field distribution, leading to non-uniform Li deposition/stripping upon repeated charge/discharge. Herein, a facile chemical reduction process is being opted to fabricate a highly Li-ion diffusive Li-Sn-based artificial SEI layer on the lithium metal surface to prevail over the above-mentioned issues. Therefore, upon careful concentration investigation of reactants, 25 mM precursor concentration (SnCl 4 in EC: DMC in 1:1 volume ration) demonstrated the best electrochemical performance, revealing a cumulative capacity of over 700 mAh/cm 2 at a current density of 1 mA/cm 2 for 1 h in a symmetric cell. Physical characterizations (XRD and SEM-EDS) showed a thin layer containing Li-Sn alloys along with LiCl formed at the lithium metal surface. Possessing high Li-ion diffusivity, Li-Sn alloyed hybrid anode illustrated a gradual decrease in the charge transfer resistance on increasing the concentration, thus, lower overpotential in symmetric cells, in contrast to pristine Li-metal. However, an increase in the electrical resistance has been observed on increasing the precursor concentration due to the presence of the insulating LiCl phase in the protective layer. Moreover, in-situ optical microscopy demonstrated more uniform and on-surface Li-deposition for the hybrid electrode, whereas mossy and dendritic growth on bare Li-metal. Full cells prepared with Li-Sn alloyed anode against NMC532 cathode illustrated stable cycling up to 150 cycles; contrastingly, the cell with pristine Li-metal showed a drastic capacity fade just after 100 cycles, demonstrating the inclination towards safer lithium metal batteries.

Lithium spreading layer consisting of nickel particles enables stable cycling of aluminum anode in all‐solid‐state battery

A Bifunctional Composite Artificial Solid Electrolyte Interphase for High Stable Solid-State Lithium Batteries

A Dynamically Stable Sulfide Electrolyte Architecture for High-Performance All-Solid-State Lithium Metal Batteries

An artificial layer enables in situ generation of a homogeneous inorganic/organic composite solid electrolyte interphase for stable lithium metal batteries

A Facile Way to Construct Stable and Ionic Conductive Lithium Sulfide Nanoparticles Composed Solid Electrolyte Interphase on Li Metal Anode

A Salt‐in‐Metal Anode: Stabilizing the Solid Electrolyte Interphase to Enable Prolonged Battery Cycling

A Porous Li-Al Alloy Anode toward High-Performance Sulfide-Based All-Solid-State Lithium Batteries

In-situ constructed polymer/alloy composite with high ionic conductivity as an artificial solid electrolyte interphase to stabilize lithium metal anode

Stable lithium metal anode enabled by a robust artificial fluorinated hybrid interphase

Li plating on alloy with superior electro-mechanical stability for high energy density anode-free batteries

Favorable Interfacial Chemomechanics Enables Stable Cycling of High-Li-Content Li–In/Sn Anodes in Sulfide Electrolyte-Based Solid-State Batteries

Improvement of the Interface between the Lithium Anode and a Garnet-Type Solid Electrolyte of Lithium Batteries Using an Aluminum-Nitride Layer

Interficial Engineering of Lithium Metal Anode for Sulfide Solid State Batteries

Compositional Engineering of Lithium Metal Anode for High‐Performance Garnet‐Type Solid‐State Lithium Battery

Constructing a High‐Strength Solid Electrolyte Layer by In Vivo Alloying with Aluminum for an Ultrahigh‐Rate Lithium Metal Anode

Li-Sn Alloyed Layer Containing Artificial SEI on Li-Metal Anode for Superior Lithium Metal Batteries: Development and Understanding of Anode/Electrolyte Interfacial Phenomena

In-situ Generated Li3N/Li-Al Alloy in Reduced Graphene Oxide Framework Optimizing Ultra-Thin Lithium Metal Electrode for Solid-State Batteries

A Li3Bi/LiF interfacial layer enabling highly stable lithium metal anode

Favorable Interfacial Chemomechanics Enables Stable Cycling of High Li-Content Li-In/Sn Anodes in Sulfide Electrolyte Based Solid-State Batteries

LiBr–LiF‐Rich Solid–Electrolyte Interface Layer on Lithiophilic 3D Framework for Enhanced Lithium Metal Anode

Dynamic Concentration of Alloying Element on Anode Surface Enabling Cycle‐Stable Li Metal Batteries