Abstract:The information presented in the article is an overview of the possibility of improving the mechanical properties of metals, alloys and sprayed coatings in order to obtain a dispersed, in particular, nanoscale substructure, which allows obtaining a set of unique operational characteristics, which, in turn, will increase the resource of parts of machines and mechanisms that are used in mechanical engineering.Today, the most common methodof nanostructuring is intensive plastic deformation (by friction, by equal-channel angular pressing, etc.), however, these methods can only be used for the manufacture of parts with a small cross-section, so the creation of new methods of deformation-thermal treatment is an urgent task of modern materials science.The paper shows the possibility of applying pre-deformation and pre-recrystallization heat treatment for technically pure iron, carbon steels of 1020 (сталь 20), 1045 (сталь 45), 1070 (сталь 70),A284Gr.D (Ст3) and C80W (У8) brands, alloyed steels of 5140H (40Х) and AISI 420 (20Х13) brands, Sv-08G2S (Св-08Г2С) gas-thermal and electric arc coatings, as well as Ni80Cr20 nichrome alloy and CuA19Mn2 (2.0960) bronze (БрАМц9-2).The work compares methods of static deformation with methods of intensive plastic deformation and shows that pre-recrystallization heat treatment allows to significantly strengthen metals (more than 30%) in combination with sufficient plasticity (for A284Gr.D (Ст3) steel, the relative elongation is up to 7.5%, and the relative narrowing is up to 75 %).The work presents the results of the experimental investigation of the influence of deformation and thermal factors on the mechanical properties, in particular, hardness and strength, of metals, alloys and sprayed coatings. It is established that the strengthening effect occurs due to the refinement of substructural elements, such as the size of coherent scatteringregions, the disorientation angle of subgrains, and the number of substructural elements to a nanoscale state. Thus, with the help of additional deformation followed by pre-recrystallization and heat treatment of carbon and alloyed steels, it is possible to obtain subgrains with a size of less than 200 nm with a disorientation angle of up to 2 ° with a relative amount of nanoscale subgrains of up to 65%.The possibility of industrial application of the proposed technology is shown on the example of production of regulating springs of membrane valves of pipelines made of 1070 (сталь 70) steel, which allows to increase the hardness by 19%.

Influence of the Metal Structure and Plastic Deformation on the Nonlinear Acoustic Parameter

Acoustic Softening and Residual Hardening in Aluminum: Modeling and Experiments

Acoustic anisotropy and localization of plastic deformation in aluminum alloys

Evaluation of plastic damage for metallic materials under tensile load using nonlinear longitudinal waves

Nonlinear acoustic characterization of heterogeneous plasticity in bent aluminium samples

Influence of Microstructure and Strain Hardening Rate on Acoustic Nonlinearity Parameter in Stainless Steel 316L during Tensile Loading

Nonlinear response to contact impact on the surface of an aluminum alloy AlMg6 exhibiting the Portevin-Le Chatelier effect

Investigation of the Peculiarities of Deformation and Fracture of Metals Obtained on the Basis of 3D Printing with Registration of an Acoustic Emission Signal

Using the Poisson's Ratio and Acoustic Anisotropy Parameter to Assess Damage and Accumulated Plastic Strain during Fatigue Failure of Austenitic Steels

CURRENT STATUS AND DEVELOPMENT PROSPECTS OF NANOSTRUCTURING OF DEFORMED METALS AND ALLOYS AND SPRAYED COATINGS

Influence of a Static Reversible Loading on Mechanical and Elastic Properties of Polycrystalline Aluminum Alloy AMg6

Monitoring of Thermal Aging of Aluminum Alloy via Nonlinear Propagation of Acoustic Pulses Generated and Detected by Lasers

Correlation between microstructural deformation mechanisms and acoustic parameters on a cold-rolled Cu30Zn brass

In situ nonlinear Rayleigh wave technique to characterize the tensile plastic deformation of stainless steel 316L

Determination of acoustic nonlinearity parameters using thermal modulation of ultrasonic waves

Application of Nonlinear Ultrasonic Technique to Characterize the Microresidual Strain in Metal

Monitoring of Environmental Loading Effect on the Steel with Different Plastic Deformation by Diffuse Ultrasound

Evaluation of Damage Degree of Inconel 718 Alloy with the Use of Non-Destructive Methods

MODELING AND EXPERIMENTAL INVESTIGATION OF THE EFFECT OF MECHANICAL STRESSES AND DAMAGE OF METAL OF OIL AND GAS EQUIPMENT ON THE PARAMETERS OF ELECTROMAGNETIC-ACOUSTIC CONVERSION

Determining the Stages of Deformation and Destruction of Composite Materials in a Static Tensile Test by Acoustic Emission