Abstract:Effects of varied levels of cerium (28 × 10–6, 65 × 10–6 and 150 × 10–6) on inclusions in a high-carbon chromium bearing steel at different stages (before adding cerium, after adding cerium for 1, 5, 10 min and ingot) were studied using laboratory experiments. An automatic scanning electron microscope system with energy-dispersive spectroscopy was used to analyze the amount, composition, size and morphology of inclusions in the steel at different stages. When the cerium content in the molten steel increased from 0 to 150 × 10–6, the evolution sequence of inclusions was as follows: Al2O3 → CeAl11O18 → CeAlO3 → Ce2O2S. After 28 × 10–6 cerium was added, Al2O3 inclusions were modified into CeAl11O18 inclusions in the molten steel and then were further transformed into Al2O3 and CeAlO3 inclusions in the solid steel during cooling. With the addition of 65 × 10–6 cerium, inclusions in the molten steel were modified into CeAlO3 and a small number of Ce2O2S inclusions. When the addition amount of cerium increased to 150 × 10–6, inclusions were transformed to Ce2O2S. The size of inclusions in the molten steel decreased obviously with cerium addition. On the other hand, the size of inclusions increased during the cooling process in solid steels of No. 1 steel (with 28 × 10–6 cerium) and No. 2 steel (with 65 × 10–6 cerium). During the cooling process, unmodified MnS inclusions were precipitated in the solid steel of No. 1 steel and wrapped outside the Al2O3 and CeAlO3 inclusions to form large complex inclusions. During the cooling process of No. 2 steel, the inclusion size of CeAlO3 increased due to the collision and polymerization. In the No. 3 steel (with 150 × 10–6 cerium), the average size of inclusions decreased rapidly and remained at a lower size during the cooling process, which was beneficial to improving the fatigue life of the steel.

Study on the Evolution of Inclusions in Ce-Modified M50NiL Steel Through the CALPHAD Approach and a Novel Inclusion Prediction Condition

Cerium Addition Effect on Modification of Inclusions, Primary Carbides and Microstructure Refinement of H13 Die Steel

Influence of Refractory-Steel Interfacial Reaction on the Formation Behavior of Inclusions in Ce-containing Stainless Steel

Study on Influence of Rare Earth Ce on Micro and Macro Properties of U75V Steel

Evolution Mechanism of Inclusions in H13 Steel with Rare Earth Magnesium Alloy Addition

Influence of cerium treatment on inclusion modification and as-cast microstructure of high-strength low-alloy steel

Effect of Cerium Content on the Evolution of Inclusions and Formation of Acicular Ferrite in Ti-Mg-Killed EH36 Steel

Evolution of Inclusions with Cerium Addition and Effects of C-containing Rare Earth Inclusions on the Toughness of Ultra-High-strength Structural Steel

First‐Principles Calculation and In Situ Observation on the Precipitation of Inclusions during Solidification of a High Sulfur Steel

Effect of Cerium Addition on Microstructure and Mechanical Properties of As-Cast High Grade Knives Steel

Effect of Cerium on Inclusion Evolution and Pitting Corrosion of Nb-Microalloyed Steel.

Effect of cerium addition on non-metallic inclusions in a high-carbon chromium bearing steel

Optimization of Inclusion and Microstructure of As‐Cast Nonquenched and Tempered Steel F38MnVS with Trace Ce

Effects of Cerium Content on the Nonmetallic Inclusions and Impact Toughness of Transformation‐Induced Plasticity Steel

Thermodynamics of the Formation of Non-Metallic Inclusions during the Deoxidation of GCr15 Bearing Steel

Evolutions of Microstructure by Cerium Treatment in As‐Cast M2 High‐Speed Steel

Evolution behaviour of inclusions via oxide metallurgy of NM450 ultrahigh-strength steel

Effects of Ce addition on mechanical properties and thermal expansion behavior of Fe-36Ni Invar alloy

Effect of Ce Addition on Inclusions and Primary Carbide Network in AISI 440C Bearing Steel

Evolution mechanism of inclusions during refining and continuous casting process of 321H stainless steel