Abstract:Studying the laser welding (LW) of three-dimensional printed materials is of important significance for developing the composite manufacturing of large structures that combines additive manufacturing and welding. Taking a laser powder bed fusion (LPBF) TC11 thin-walled cylinder as the base metal (BM), joints obtained by LW and existing electron beam welding (EBW) procedure were compared in terms of microstructures and mechanical properties. In addition, the joints were annealed at 950 degrees C for 0.5 h, followed by air cooling to room temperature, and then heated to 580 degrees C for 2 h, followed by air cooling. The microhardness of the as-welded LW joint is slightly higher than that of EBM joints on the whole. The heat affected zone (HAZ) of as-welded LW joint shows the lowest microhardness, which is 413.7 +/- 15.4HV on average. While alpha ' phases are decomposed, dislocation density reduces, and alpha '/alpha phases are coarsened in FZ of EBW joint, so FZ of EBW joints exhibits the lowest microhardness, being 398.4 +/- 11.7HV on average. After annealing, the distribution trends for microhardness of the two types of joints both remain unchanged. Before annealing, the strength and plasticity of laser welded joints are higher, at 1395.7 +/- 64.6 MPa and 6.94 +/- 0.08%, respectively. After annealing, the width of alpha phases in the joints increases obviously, and globular alpha phases with a small length-to-width ratio appear in FZ of EBW joint, which to some extent improves the ability to coordinate deformation. Therefore, the EBW joints achieve a better balance between strength and plasticity, with average values of 1103.1 +/- 34.9 MPa and 9.37 +/- 0.20%, respectively. These joints all fracture at FZ, showing mixed fracture and ductile fracture before and after annealing. The above results indicate that the composite manufacturing combining AM and welding based on LW is feasible.

Mechanical properties of CO2 laser beam butt-welded plates of Hastelloy c-276

Mechanical properties of butt weldments made with E5515-G electrodes at high temperature

The Microstructures and Mechanical Properties of a Welded Ni-Based Hastelloy X Superalloy

Fatigue behaviour of a laser beam welded CoCrFeNiMn-type high entropy alloy

Mechanical property and microstructure of HSLA steel laser hybrid welded joint

Joint performance of CO2 laser-MIG hybrid welding 5083-H116 alloy

Microstructure and mechanical analysis of SS321 in CO2 laser beam welding joint

Mechanical properties of Hastelloy X produced by laser powder bed fusion and affected by spatter redeposition

Microstructures, mechanical properties and corrosion resistance of Hastelloy C22 coating produced by laser cladding

Interactions of the process parameters and mechanical properties of laser butt welds in thin high strength low alloy steel plates

Effects of heat input on the mechanical properties of butt-welded high and ultra-high strength steels

Effect of post-weld heat treatment on the microstructure, phase composition and mechanical properties of dissimilar Al-Mg-Li/Al-Cu-Li laser welded joints

Microstructure and Tensile Properties of Microwave Welded Hastelloy C-276 Joints

Stress and distortion of the 10 mm thick plate EH40 and 316L different butt joints in 10 kW laser welding

Microstructure and Mechanical Properties of Superalloy Laser Welded Joints for GH3625 Fabricated by Laser Additive

Microstructure, Mechanical Properties and Fatigue Crack Growth Behavior of Gas Tungsten Arc Welding Welded Joint of the Hastelloy N Alloy

Effect of Beam Displacement on Joint Properties of Laser Welding DD407/GH1140 Joint

Laser heat conduction joining of polycarbonate and aluminum alloy

Comparison of Performance of Laser Powder Bed Fusion Thin-Walled TC11 Alloy Samples Welded Via Laser Welding and Electron Beam Welding

Microstructure and Mechanical Property in Heat Affected Zone (HAZ) in F82H Jointed with SUS316L by Fiber Laser Welding

Microstructure and Mechanical Properties of High Power CO2 Laser Welded Inconel 625 Nickel Based Alloy