Abstract:The microstructure evolution of Mg-3Sn, Mg-3Sn-3Al-Zn (ATZ331), and Mg-3Sn-6Al-Zn (ATZ631) alloys during high-speed rolling (HSR) and annealing was studied. High-speed rolling was carried out on the three alloys at a rolling speed of 1100 m/min, a rolling temperature of 400 °C, and a reduction of 40% during a single pass. The results showed that the microstructure of the samples after HSR contained many twins and was dominated by {10−12} extension twins (ETs) and supplemented by {10−11} contraction twins (CTs) and {10−11}-{10−12} double twins (DTs). After adding Al, the content of these different types of twins was reduced. The twinning fraction decreased significantly with 3 wt% Al addition, while the twinning fraction decreased slightly with 6 wt% Al addition. The high-speed rolled alloys were annealed at 370 °C for 1 min, 2 min, 3 min, 5 min, and 8 min. When the annealing time was 1 min, the recrystallization fraction of the ATZ631 alloy was low, indicating that increasing the Al content to 6 wt% inhibited recrystallization. When the annealing time increased to 3 min, the recrystallized grains in the ATZ631 alloy grew, indicating that the grain growth progressed faster in this alloy. When the annealing time was 8 min, the grain size of the three alloys grew. The electron backscattered diffraction (EBSD) results of the alloy annealed for 8 min showed that the twin fraction in the annealed state was lower than that after high-speed rolling. In addition with the increase in Al content, the twin fraction decreased. During high-speed rolling, the maximum intensity also increased with an increase in Al content, were 22.72, 25.09, and 26.35, and the texture of the annealed alloy was weakened. The Al addition also increased the maximum intensity.

Inherited effect of original loading direction on the annealing behavior of a hot-compressed Mg-1.0 wt%Ca sheet

Effect of Mg on Nucleation Process of Recrystallization in Al–Mg–Si/SiCp Composite

Effect of annealing treatment on the microstructure and mechanical properties of warm-rolled Mg–Zn–Gd–Ca–Mn alloys

Hot deformation behavior of novel high-strength Mg-0.6Mn-0.5Al-0.5Zn-0.4Ca alloy

Effect of rolling temperature on microstructure and mechanical properties of hot-rolled Mg-Al-Ca-Zn-Mn alloys

Effects of annealing treatment on microstructure and tensile behavior of the Mg-Zn-Y-Nd alloy

Insights into the evolution of texture and mechanical properties during warm rolling and annealing of Mg–2Zn-0.5Ca alloy

Effect of pack-rolling temperature on microstructure and mechanical properties of Mg-6Sn-3Al-1Zn Alloy

Hot Deformation Behavior and Microstructural Evolution of Twin-Roll-Casting Mg Alloy during High-Temperature Compression

Microstructure evolution and mechanical property of Mg-3Al alloys with addition of Ca and Gd during rolling and annealing process

Effect of rolling temperature on deformation behavior and mechanical properties of Mg-8Li-1Al-0.6Y-0.6Ce alloy

The effect of grain size on deformation modes and deformation heterogeneity in a rolled Mg-Zn-Ca alloy

Influence of Ca Content on Microstructure and Mechanical Properties of Extruded Mg–Al–Ca–Mn Alloys

Effect of Heat Treatment on Microstructure and Properties of Rolled Mg-4Y-3Nd-1.5Al Alloy

Preferential grain growth and textural evolution of AZ31B Mg alloy during annealing after isothermal compression at 400 °C

Hot compression behavior and microstructure evolution of Mg-Gd-Y-Zn-Zr alloy

Strength-ductility balance of Mg-1.03Ca-0.47Mn Mg alloy sheet produced by rolling and annealing

Effect of Al addition and annealing on the microstructure evolution of Mg-3Sn Mg alloy subjected to high-speed rolling

Effect of annealing treatment on texture evolution, microstructure and mechanical properties of an extruded Mg-Gd-Zn-Zr alloy

Role of Al addition in modifying microstructure and mechanical properties of Mg-1.0 wt% Ca based alloys

Microstructure and mechanical properties synergistically enhanced via heat treatment modification of the as-extruded Mg-1.5Al-0.5Zn-0.2Y-0.2Ca alloy