Abstract:The polymer electrolyte membrane fuel cell is a power source with the potential for reducing green-house gas emissions. Characterizing the electrolyte of a fuel cell is an important procedure for assessing the performance of the entire device. Atomic force microscopy (AFM) is one of the major instruments for such characterization, since it can be used for determining the surface potential and/or charge distributions in a fuel cell electrolyte. In order to understand the mechanisms involved in the AFM imaging of the membrane material, we have been developing detailed models that are able to describe the contributions from sample properties and AFM probe tip geometry to the AFM images. In the past year, we have extended our initial model to take into account fuel cell electrolyte materials that are dielectric with spatial variation in charge distributions. This development allows us to accurately predict AFM images based on knowledge of the sample charge distribution and to characterize the resolution of the AFM. The proposed numerical method developed in this project also provides insights for the development of new algorithms for reconstructing sample charge distributions from AFM images, which would provide a comprehensive quantitative evaluation of fuel cell devices. Introduction Solid polymer fuel cells promise to be an efficient power source for mobile and stationary applications with the potential for a greatly reduced environmental impact. However, the ionic diffusion behavior under current load conditions in the ion-selective membranes of proton exchange membrane fuel cells (PEMFCs) is not completely understood. Further understanding of ion behavior at the Nernst diffusion layer of the membrane surface could enable development of new classes of solid polymer fuel cell membranes with increased mass transport. In this project we are examining and characterizing the properties of solid polymer membranes through analytical and numerical modeling of ion transport, impedance, diffusion and atomic force microscopy imaging. To address the challenges of enabling new solid polymer fuel cell membranes, the project has four primary objectives: 1. Atomic force microscope imaging. Nanoscale AFM surface imaging of dielectric or polarizable fuel cell materials involves complex AFM tip interactions with unknown surface and space charges resulting in electrostatic and van der Waals forces. Nonlinear modeling will be employed to solve the inverse problem of finding the charge distributions from AFM images with the goal of elucidating the mechanisms of charge motion in fuel cell and biological media relevant for environmental cleanup. 2. Simulation of impedance measurements. Modeling and simulation of AFM impedance measurements in fuel cells to shed light on the effects of probe tip geometry and surface roughness and topography with goal of developing scaling laws for fuel cell performance. 3. Modeling of ionic transport in PEMFC’s. Analytical and numerical modeling of ionic diffusion in fuel cells taking into account electrochemical kinetics, current distribution, hydrodynamics and multi-component transport with the goal of elucidating mass transport characteristics. 4. Particle diffusion modeling. In order to further understand mechanisms of ion and solvent transport in hydrated PEMFC membranes, modeling that accounts for local molecular information will be employed. Our primary efforts have been directed to the first objective. Figure 1: Schematic of the AFM tip (without the cantilever) and the sample

Analysis of Transmission Line Models for PEMFC Impedance Modelling

A Two-Dimensional Analysis of Mass Transport in Proton Exchange Membrane Fuel Cells

Electron Transport in PEFCs

Modeling Analysis of Polymer Electrolyte Membrane Fuel Cell with Regard to Oxygen and Charge Transport under Operating Conditions and Hydrophobic Porous Electrode Designs

Numerical Modeling of Liquid Water Transport Inside and Across Membrane in PEM Fuel Cells

Impedance Characteristics of Cell-to-Cell Inconsistency of Polymer Electrolyte Membrane Fuel Cells

Small-Signal Electrical Model of PEM Fuel Cell

Sensitivity analysis of structural parameters for PEMFCs based on 1D transient model and elementary effect method

Steady-State Voltage Modelling of a HT-PEMFC under Various Operating Conditions

Electrochemical Impedance Analysis with Transmission Line Model for Accelerated Carbon Corrosion in Polymer Electrolyte Membrane Fuel Cells

Study on Relationship Between Low-Frequency Impedance and Internal States of Polymer Electrolyte Membrane Fuel Cell Based on Mass Transfer and Impedance Model

Parameter Identification of a Quasi-3D PEM Fuel Cell Model by Numerical Optimization

Effects of various parameters of different porous transport layers in proton exchange membrane water electrolysis

Multiscale study of reactive transport and multiphase heat transfer processes in catalyst layers of proton exchange membrane fuel cells

Modeling , Simulation and Characterization of Atomic Force Microscopy Measurements for Ionic Transport and Impedance in PEM Fuel Cells : GCEP Technical Report 2007

Unveiling the Mechanisms Behind Temperature-Dependent Impedance Behavior in Polymer Electrolyte Fuel Cells at High Current Loads

A new insight into the effects of agglomerate parameters on internal dynamics of proton exchange membrane fuel cell by an advanced impedance dimension model

Experimental parameter uncertainty in PEM fuel cell modeling. Part I: Scatter in material parameterization

In-situ Impedance Diagnosis Experiment and Equivalent Circuit Modeling Based on Distribution of Relaxation Time Method for Unitized Regenerative Proton Exchange Membrane Fuel Cells

Parameter Sensitivity Examination and Discussion of PEM Fuel Cell Simulation Model Validation

Classification, summarization and perspective on modeling techniques for polymer electrolyte membrane fuel cell