Abstract:Especially in the electric vehicle industry where both high energy density and long lifetime batteries are sought, Ni-based cathode materials such as LiNi 1−x−y Mn x Co y O 2 (NMC) and LiNi 1−x−y Co x Al y O 2 (NCA) provide a fitting compromise in capacity and cyclability. In recent years, the high cost of cobalt in addition to the problematic geopolitics surrounding cobalt mining have motivated research efforts toward cobalt-free cathode materials. 1 However, Ni-rich materials are subject to inevitable failure mechanisms such as microcracking and parasitic reactions with the electrolyte which are further aggravated with an increase in Ni-content and in the absence of Co. 2 Many strategies have been proposed to overcome these challenges such as doping and/or coating the cathode particles, 3 but there remains a need to further increase energy density with minimal compromise to lifetime. In this work we present a cathode active material system designed to push Ni-rich and Co-free materials to the limit of their performance. This is done by choosing optimal polycrystalline particle size, a balance of Mn and Al content, and a sufficient amount of high-valence doping. Additionally, appropriate synthesis conditions are needed to obtain the desired morphology and infuse the intergranular boundaries with the W dopant. It is then important to choose an appropriate upper cutoff voltage during cycling to maximize energy while avoiding drastic crystal changes. 4 This optimized NMA-W material system delivers specific capacity above 200 mAh/g while retaining 95% of its capacity without relying on any amount of Co. The series of NMA-W materials presented in this work were characterized and tested. Scanning electron microscopy (SEM) images were used to observe morphology and crystallite growth after synthesis. X-ray diffraction (XRD) analysis was conducted to monitor the crystal parameters and accelerated rate calorimetry (ARC) was used to assess the thermal stability and safety of the material. Compression tests were also conducted to study the strength of the particles and their propensity to crack under stress. Choi, J. U., Voronina, N., Sun, Y. K. & Myung, S. T. Recent Progress and Perspective of Advanced High-Energy Co-Less Ni-Rich Cathodes for Li-Ion Batteries: Yesterday, Today, and Tomorrow. Adv. Energy Mater. 10 , 1–31 (2020). Li, H. et al. An Unavoidable Challenge for Ni-Rich Positive Electrode Materials for Lithium-Ion Batteries. (2019) doi:10.1021/acs.chemmater.9b02372. Yan, W., Yang, S., Huang, Y., Yang, Y. & Guohui Yuan. A review on doping/coating of nickel-rich cathode materials for lithium-ion batteries. J. Alloys Compd. 819 , 153048 (2020). Nam, G. W. et al. Capacity Fading of Ni-Rich NCA Cathodes: Effect of Microcracking Extent. ACS Energy Lett. 4 , 2995–3001 (2019).

Versatile High-Valent Doping Strategy for Cathodes with Extremely High Ni Content

Multifunctional Doping Strategy to Develop High‐Performance Ni‐Rich Cathode Material

Enhancing high-voltage performances of nickel-based cathode material via aluminum and progressive concentration gradient modification

Mitigation of Cation Mixing of LiNiO2-based Cathode Materials by Li-doping for High-Performing Lithium-Ion Battery

Two birds with one stone: One-pot concurrent Ta-doping and -coating on Ni-rich LiNi0.92Co0.04Mn0.04O2 cathode materials with fiber-type microstructure and Li+-conducting layer formation

Enhancing The Cycling Stability Of Ni-Rich Lini0.6co0.2mn0.2o2 Cathode At A High Cutoff Voltage With Ta Doping

Enhancing the Cycling Stability of Ni-Rich LiNi<sub>0.6</sub>Co<sub>0.2</sub>Mn<sub>0.2</sub>O<sub>2</sub> Cathode at a High Cutoff Voltage with Ta Doping

Pushing the Energy-Lifetime Frontier of Li-Ion Batteries with Optimized Ni-Rich, Co-Free NMA-W Cathodes

Comprehensive study of tantalum doping on morphology, structure, and electrochemical performance of Ni-rich cathode materials

Comprehensive study of Ti and Ta co‐doping in Ni‐rich cathode material LiNi0.8Mn0.1Co0.1O2 towards improving the electrochemical performance

Improved High-Voltage Cycling Stability of Single-Crystalline LiNi0.8Co0.1Mn0.1O2 Cathode by Tantalum Doping

Ta/Ti Codoped Concentration Gradient High-Ni Cathodes for Long-Life Li-Ion Batteries

Surface Engineering of Ni-Rich Cathodes Enables Homogeneous Doping of High-Valence Mo Ions for Li-Ion Batteries

High‐Energy Ni‐Rich Cathode Materials for Long‐Range and Long‐Life Electric Vehicles

Site-dependent multicomponent doping strategy for Ni-rich LiNi1−2yCoyMnyO2 (y = 1/12) cathode materials for Li-ion batteries

Ta doping and LiTaO3 coating to improve the electrochemical performance of LiNi0.925Co0.03Mn0.045O2 cathode material for lithium ion batteries

Engineering a Robust Interface on Ni-Rich Cathodes via a Novel Dry Doping Process toward Advanced High-Voltage Performance

Enhancing the Structural Stability and Electrochemical Performance of High-Nickel Cathode Materials through Ti Doping with an Exothermic Non-oxide Precursor

Lanthanum doping and surface Li 3 BO 3 passivating layer enabling 4.8 V nickel-rich layered oxide cathodes toward high energy lithium-ion batteries

Tellurium Surface Doping to Enhance Structural Stability and Electrochemical Performance of Layered Ni-rich Cathode.

A universal multifunctional dual cation doping strategy towards stabilized ultra-high nickel cobalt-free lithium layered oxide cathode