Abstract:Ni-rich layered oxides have become the main force of cathode materials for EV cells with high energy density owing to their satisfactory theoretical capacity, cost-effectiveness, and low toxicity. However, the high-voltage stability of Ni-rich cathode materials still has not fulfilled the demand of power batteries due to their intrinsic structural and electrochemical instability. The commonly used modification procedures are achieved via a wet process, which may lead to surface lithium-ion deficiency, phase change, and high costs during manufacturing. Herein, we construct a multifunctional Ti-based interfacial architecture on the surface of LiNi0.6Co0.2Mn0.2O2 (NCM) cathode materials via a novel dry interface modifying process in which no solvent is employed. The Ti-based interfacial architecture accelerates the transportation of lithium ions and consequently stabilizes the interfacial structure. This approach significantly improves the cycling stability in half cells, with a 15% increase in capacity retention over 100 cycles at 1 C under a high voltage of 4.5 V. Impressively, few internal cracks are observed in a modified sample after 500 times of charge and discharge between 2.75 and 4.35 V at 1 C rate, and the capacity retention can reach 93%.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c12803.XRD patterns and SEM images for all samples, HRTEM image of NCM-T2, single GITT titration curves, voltage as a function of square root of time for a single charging current pulse duration with the corresponding linear fit, XRD Rietveld refinement lattice parameters, and fitted electrochemical impedance parameters (PDF)This article has not yet been cited by other publications.

A Comprehensive Solution for Ni-Rich Cathodes by Lithium Silicate Coating

Enhancing high-voltage performances of nickel-based cathode material via aluminum and progressive concentration gradient modification

Radially Oriented Single‐Crystal Primary Nanosheets Enable Ultrahigh Rate and Cycling Properties of LiNi0.8Co0.1Mn0.1O2 Cathode Material for Lithium‐Ion Batteries

Surface Coating with Li-Ti-O to Improve the Electrochemical Performance of Ni-rich Cathode Material

Sol/Antisolvent Coating for High Initial Coulombic Efficiency and Ultra-stable Mechanical Integrity of Ni-Rich Cathode Materials

Nanoscale operation of Ni-Rich cathode surface by polycrystalline solid electrolytes Li3.2Zr0.4Si0.6O3.6 coating

Stabilizing high-Ni cathodes with gradient surface Ti-enrichment

New insights into dry-coating-processed surface engineering enabling structurally and thermally stable high-performance Ni-rich cathode materials for lithium ion batteries

Surface enrichment and diffusion enabling gradient-doping and coating of Ni-rich cathode toward Li-ion batteries

An integrated surface coating strategy to enhance the electrochemical performance of nickel-rich layered cathodes

A short process and low-cost preparation of single crystal LiNi0.6Co0.2Mn0.2O2 cathode for lithium-ion batteries

Improving rate capacity and cycling performance of lithium-rich high-Mn Li-1.8[Mn0.7Co0.15Ni0.15]O-2.675 cathode materials by Li2SiO3 coating

Realizing the Single-Crystalline LiNi 0.90 Mn 0.05 Co 0.05 O 2 Cathode with Long-Life and High-Safety Property Driven by Polysiloxane Covering and PO43- Doping

Improving the Electrochemical Performance of Ni-rich Cathode Material LiNi 0.815 Co 0.15 Al 0.035 O 2 by Removing the Lithium Residues and Forming Li 3 PO 4 Coating Layer

Engineering a Robust Interface on Ni-Rich Cathodes via a Novel Dry Doping Process toward Advanced High-Voltage Performance

Li2sio3 Coating to Improve the High-Voltage Performance of Lini1/3co1/3mn1/3o2 Cathode

Integrating Trace Ti-doping and LiYO2-coating to Stabilize Ni-rich Cathodes for Lithium-Ion Batteries

Lithium-conductive LiNbO3 Coated High-Voltage LiNi0.5Co0.2Mn0.3O2 Cathode with Enhanced Rate and Cyclability

Protective and ion conductive: High-Rate Ni-Rich cathode with enhanced cyclic stability via One-Step bifunctional dual-layer coating

Integrated co-modification of PO43− polyanion doping and Li2TiO3 coating for Ni-rich layered LiNi0.6Co0.2Mn0.2O2 cathode material of Lithium-Ion batteries

Stabilizing Surface Chemistry and Texture of Single-Crystal Ni-rich Cathodes for Li-ion Batteries