Abstract:Выполнена экспериментальная (метод максимального давления в газовом пузыре) оценка плотности и поверхностного натяжения гомогенных расплавленных шлаков совместной плавки силикатной никелевой и медной колчеданной руд. Измерения проведены на модельных образцах: железистого, масс. % (8,9 CaO; 11,8 MgO; 12,5 Al2O3; 47,4 SiO2; 13,3 FeO и 5,0 Fe2O3) и образованного при удалении из него оксидов железа безжелезистого, масс. % (12,5 CaO; 16,0 MgO; 9,4 Al2O3 и 58,3 SiO2) шлаков, отражающих состав и структуру реальных прототипов, в интервалах температур 1550–1300 °C и 1550–1400 °C соответственно. Снижение температуры ведет к повышению плотности и поверхностного натяжения указанных шлаков в диапазонах 1,85–2,21 и 2,23–2,29 г·см–3 и 144–250 и 340–345 мН·м–1 соответственно. Структурные изменения при переходе от первого состава ко второму вызваны сокращением основности с 0,7 до 0,6 и заменой Fe2+ на Ca2+ и Mg2+. Второй фактор вносит основной вклад в рост как самих характеристик, так и их температурных коэффициентов (от –0,0015 до –0,0004 г·см–3·°C–1 и от –0,4 до –0,1 мН·м–1·°C–1 соответственно). Методом регрессионного анализа экспериментальных данных получены эмпирические модели, позволяющие достоверно прогнозировать величину плотности и поверхностного натяжения реальных шлаков рудной плавки медного и никелевого сырья в рассмотренном диапазоне температур. Результаты работы могут быть использованы при разработке и совершенствовании металлургических технологий, а также процессов стекольной и керамической промышленности. An experimental (method of maximum pressure in a gas bubble) assessment of the density and surface tension of homogeneous molten slags from the joint smelting of nickeliferous saprolitic and copper pyrite ores has been carried out. The measurements were made on model samples of iron-containing (8.9 wt. % CaO; 11.8 wt. % MgO; 12.5 wt. % Al2O3; 47.4 wt. % SiO2; 13.3 wt. % FeO and 5.0 wt. % Fe2O3) and formed upon removal of iron oxides from it iron-free (12.5 wt. % CaO; 16.0 wt. % MgO; 9.4 wt. % Al2O3 and 58.3 wt. % SiO2) slag, reflecting the composition and structure of real prototypes, in the temperature ranges of 1550–1300 °C and 1550–1400 °C, respectively. A decrease in temperature leads to an increase in the density and surface tension of these slags in the ranges of 1.85–2.21 and 2.23–2.29 g·cm–3 and 144–250 and 340–345 mN·m–1, respectively. Structural changes during the transition from the first composition to the second are caused by a reduction in basicity from 0.7 to 0.6 and the replacement of Fe2+ by Ca2+ and Mg2+. The second factor makes the main contribution to the growth of both the characteristics themselves and their temperature coefficients (from –0.0015 to –0.0004 g·cm–3·°C–1 and from –0.4 to –0.1 mN·m–1·°C–1, respectively). Using the method of regression analysis of experimental data, empirical models have been obtained that make it possible to accurately predict the density and surface tension of real slags from the smelting of copper and nickel raw materials in the considered temperature range. The results of the work can be used in the development and improvement of metallurgical technologies, as well as in the glass and ceramic industries.

DENSITY AND SURFACE TENSION OF SLAGS FROM THE JOINT SMELTING OF NICKELIFEROUS SAPROLITIC AND COPPER PYRITE ORES

Density, viscosity and surface tension of high-silicate CaO–SiO2 and CaO–SiO2–Fe2O3 slags derived by aerodynamic levitation. The behavior of Fe3+ in high-silicate melts

THERMODYNAMICS OF COPPER AND LEAD IN ALUMINA SATURATED FLASH SMELTING SLAG

Reconstruction of Copper Smelting Technology Based on 18–20th-Century Slag Remains from the Old Copper Basin, Poland

High-Temperature Rheometric and Melting Experiments of Refining-Type Ladle Slag Systems

Artificial Slags with Modulated Properties for Controlled Nickel Dissolution in Smelting Process

Modeling of Exchange Interactions in Melts Formed During Joint Smelting of Oxidized Nickel Ores and Pyrrhotite Concentrates

Experimental Study on the Phase Equilibrium of Copper Matte and Silica-Saturated FeO X -Sio 2 -Based Slags in Pyrometallurgical WEEE Processing

Crystallization ability of glasses based on slags from the joint smelting of silicate nickel and copper pyrite ores

Behavior of copper and lead during mineralurgical and hydrometallurgical processing of flash smelting slag

APPLICATION OF SOLID SLAG MIXTURES BASED ON ALUMINUM OXIDE IN SMELTING OF LOW-SULFUR STEEL

Effect of SiO2 and Al2O3 on the Thermophysical Properties and the Foaming Index of Electric Arc Interface Slag from the Production of Construction Steel

Equilibrium of Copper Matte and Silica-Saturated Iron Silicate Slags at 1300 °C and $$ P_{{{\text{SO}}_{ 2} }} $$ of 0.5 Atm

Equilibrium of Copper Matte and Silica-Saturated Iron Silicate Slags at 1300 °C and PSO2\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \Setlength{\oddsidemargin}{-69Pt}

Studying the Structure and Viscosity of MnO-SiO2-CaO-Al2O3-MgO Slag System

Analysis of the Kinetics of Devitrification and Crystallization of a Melilite Mold Powder Slag for Medium Carbon Steel Billet Casting

COMPREHENSIVE WASTE-FREE PROCESSING TECHNOLOGY OF COPPER SMELTING SLAGS

Formation of optimal slag composition in ladle furnace for improvement of desulfurization properties and optimization of consumption of slag-forming materials

Chemical and Phase Reactions on the Contact between Refractory Materials and Slags, a Case from the 19th Century Zn-Pb Smelter in Ruda Śląska, Poland

KINETIC REGULARITIES OF NICKEL SULFURIC ACID LEACHING PROCESSES

A Study on the Selective Leaching of Valuable Metals and the Configuration of Iron Silicon Phases in Copper Smelting Slag by Oxidative Pressure Leaching