Abstract:The graphene nanoplatelets (GNPs) reinforced Mg-4Zn-0.5Mn (wt%) matrix composites (GNPs/ZM40) with different concentrations (0.1, 0.3, 0.5 wt%) of GNPs were processed by liquid-state molding method combined with low temperature extrusion process. The microstructure of the prepared materials was analyzed by means of scanning electron microscope (SEM) equipped with Energy Dispersive Spectroscopy (EDS), transmission electron microscope (TEM), X-ray diffractometer (XRD) and optical microscope (OM). And the tensile test at room temperature was carried out to reveal the mechanical properties of the materials. The results showed that the 0.3 wt% GNPs/ZM40 composite exhibited the outstanding mechanical properties of yield strength (YS: ∼466 MPa) and ultimate tensile strength (UTS: ∼532 MPa). In as-cast materials, the addition of GNPs led to the refinement of equiaxed grains and eutectic phases in the composites, closely related with the promotion of heterogeneous nucleation by GNPs during the solidification. After low temperature extrusion, the prominent dynamic recrystallization (DRX) took place in as-extruded alloy and GNPs/ZM40 composites, producing plenty of fine grains. In contrast to the alloy, the average grain sizes of the composites with different GNPs content were reduced, whereas the degrees of recrystallization in the composites increased. These differences in microstructural evolutions originated primarily from the inhibiting effect of GNPs on the grain growth and the boost to DRX by the high-density dislocations in magnesium matrix caused by GNPs. Accordingly, the high YS of the composites could be largely ascribed to fine-grain strengthening, dislocation strengthening effect and load transfer mechanism.

Influence of GNPs@Cu on high-temperature mechanical and thermal properties of laminated MTZ composites

Effect of Carbide Interlayers on the Microstructure and Properties of Graphene-Nanoplatelet-reinforced Copper Matrix Composites

Achieving high strength in graphene nanoplatelets reinforced Mg-Zn-Mn matrix composites via liquid-state molding technology and low temperature deformation process

Investigating the Potential of Powder Metallurgy for Fabricating Graphene Nanoplatelets Reinforced Copper Nanocomposites

Enhanced interfacial bonding and mechanical properties of (TiC p +GNPs)/Cu composites by Ti-induced GNPs/Cu interfacial modification

Fabrication and mechanical properties of nano‐carbon reinforced laminated Cu matrix composites

Simultaneously improved mechanical and thermal properties of Mg-Zn-Zr alloy reinforced by ultra-low content of graphene nanoplatelets

Damping and mechanical behavior of graphene nanoplatelets reinforced Al-30Zn alloy matrix bioinspired laminated composites by two steps flake powder metallurgy

Cu/Mo/NGs composites: Multilayer interconnected spatial net structure enhanced the mechanical properties

Mechanical and tribological properties of graphene nanoplatelets-reinforced titanium composites fabricated by powder metallurgy

Microstructure and mechanical properties of nano-carbon reinforced Mo–Cu–Zr composites

A Novel Cu–GNPs Nanocomposite with Improved Thermal and Mechanical Properties

Powder-metallurgical construction of graphene-like nanosheet network reinforced Cu composites towards balanced high-performance

Microstructures and properties of graphene nanoplatelets reinforced Cu/Ti3SiC2/C nanocomposites with efficient dispersion and strengthening achieved by high-pressure torsion

Synergistic enhancing effect of tungsten-copper coated graphite flakes and aluminum nitride nanoparticles on microstructure, mechanical and thermal properties of copper matrix composites

Achieving high strength and ductility in copper matrix composites with graphene network

Comprehensive performance regulation of Cu matrix composites with graphene nanoplatelets in situ encapsulated Al2O3 nanoparticles as reinforcement

A Novel Approach to Enhance the Mechanical Strength and Electrical and Thermal Conductivity of Cu-GNP Nanocomposites

Enhancing the Strengthening Effect of Graphene-Nanoplates in Al Matrix Composites by Heterogeneous Matrix Design

Enhancement of thermal–mechanical performances via a selective CNTs configuration in laminated CNTs/AZ31B composite

Development of Al- and Cu-based nanocomposites reinforced by graphene nanoplatelets: Fabrication and characterization