Abstract:Wire and arc additive manufacturing (WAAM) has emerged as a highly promising technique for manufacturing large-scale steel structural elements. However, the distinct mechanical properties of WAAM steel could potentially lead to different performance of WAAM steel bolted connections compared to the traditional steel bolted connections. This study aims to investigate the material properties of WAAM steel and the structural behaviours of WAAM steel bolted connections, focusing on the effects of print layer orientation and connection plate geometrical dimensions. A total number of 24 WAAM steel coupon specimens with three different print layer orientations and 36 WAAM double-shear bolted connections with two print layer orientations and different geometric dimensions were designed, fabricated and tested under monotonic tension. These specimens were measured using a 3D laser scanner and Digital Image Correlation (DIC) was adopted to measure the structural response during testing. The impact of print layer orientations on WAAM material properties and the effects of WAAM material properties on bolted connections were analysed and discussed. The current design codes for traditional steel bolted connections were evaluated against the test results of WAAM steel bolted connections. The study found that the print layer orientations of WAAM steel plates initiated an anisotropic material property of the coupon specimens, demonstrated by the differences in ultimate tensile strength and strain of specimens with different print layer orientations. Five failure modes, including net section tension, shear-out, bearing, end-splitting, and block shear failure were observed for the bolted connections. The material anisotropy further affects the performance of the bolted connections, though in the same dimensions, 28% of the specimens presented different failure modes due to the different print layer orientations. The effectiveness of current steel design standards was compromised by inaccurate predictions of failure modes due to the distinct end-splitting failure mode and the effects of material anisotropy, though the predictions of the ultimate capacities of the WAAM lap shear specimens were relatively accurate.

Investigation of tensile and fatigue properties of an austenitic stainless steel part fabricated by WAAM

Mechanical Properties, Microstructural Characteristics and Heat Treatment Effects of WAAM Stainless-Steel Plate Material

Microstructure and Mechanical Properties of 304L Steel Fabricated by Arc Additive Manufacturing

Experimental Study on Wire and Arc Additively Manufactured Steel Double-Shear Bolted Connections

Mechanical behavior of austenitic stainless steels produced by wire arc additive manufacturing

The Fracture Toughness and Fatigue Crack Growth Properties of 18ni 300 Maraging Steel Manufactured by Wire + Arc Additive Manufacturing

Fabrication and Fatigue Properties of Dissimilar Steel Functionally Graded Material Structure Through Wire Arc Additive Manufacturing

Experimental characteristics of 316L stainless steel thin wall processed in wire-based arc additive manufacturing process

Fatigue of wire arc additively manufactured components made of unalloyed S355 steel

Tensile properties and microstructural features of 304L austenitic stainless steel produced by wire-and-arc additive manufacturing

Experimental and numerical determination of the fatigue notch factor in as‐built wire arc additive manufacturing steel components

Effect of thermal history on microstructure evolution and mechanical properties in wire arc additive manufacturing of HSLA steel functionally graded components

Microstructure and Mechanical Properties of Low-Carbon High-Strength Steel Fabricated by Wire and Arc Additive Manufacturing

Fatigue and anisotropic behavior of wire-arc additive manufactured TC17 titanium alloy

Wire Arc Additive Manufactured Mild Steel and Austenitic Stainless Steel Components: Microstructure, Mechanical Properties and Residual Stresses

Characterization of a low-alloy steel component produced with wire arc additive manufacturing process using metal-cored wire

Experimental study on the heat input behavior of wire-arc additively manufactured 316L stainless steel parts for repairing applications

Fatigue crack growth behaviour of wire arc additively manufactured steels

Development of a New High Strength Alloy from Low Alloy Steel Wire by Innovative Additional Cold Wire Feeding Used in Wire Arc Additive Manufacturing

Investigations and Multi-response Optimization of Wire Arc Additive Manufacturing Cold Metal Transfer Process Parameters for Fabrication of SS308L Samples

Experimental study of shielding gas concentration on mechanical properties of stainless steel alloy parts using wire and arc additive manufacturing