Abstract:Over the last few decades, "Discontinuously Reinforced Particulate Composites (DRPCs)" are a popular class of composite materials with considerable challenge in processing, characterization and machinability because of their increased strength-weight ratio, stiffness, specific strength and oxidization when compared to various metals and their alloys. This paper discusses experimental and numerical investigation on mechanical characteristics of aluminum metal matrix reinforced with various reinforcement particulates such as silicon carbide, aluminium oxide, and zirconium oxide, compaction pressure (kN) and hold time (s) based on Design of Experiments (DOE) and Finite Element Analysis. Initially this paper discusses the process optimization of Aluminum Matrix reinforced with different particulates experimentally to identify the favourable processing conditions by varying reinforcement materials, compaction pressure (kN) and hold time (s) based on TDOE (Taguchi's Design of Experiments). Further, this paper concentrates to determine "maximum principal stress, equivalent elastic strain and equivalent (von-mises) stress" based on Finite Element Analysis (ANSYS Workbench-2023R1). The results of the experimentation showed that the highest hardness values were achieved with ZrO2 reinforcement material. Increasing the compaction pressure from 8 to 12 kN resulted in a slight decrease in surface roughness and porosity. Higher compaction pressures have assumed to facilitate better particle distribution and improved interfacial bonding, leading to smoother surfaces and lower void content. The simulation results showed that the maximum principal stress achieved were (2235.8 Mpa) SiC, (3444.4 Mpa) Al2O3, and (3582.5 MPa) ZrO2. The equivalent elastic strain achieved was (0.2488) SiC, (0.2421) Al2O3 and (0.262) ZrO2. The equivalent (Von Mises) stress achieved was (28751 MPa) for SiC, (24880 MPa) for ZrO2 and (26972 Mpa) for Al2O3. This experimentation and simulation demonstrated that the PM process can be used to fabricate DRAMMC with different reinforcement particulates.

Experimental Investigation of WE43(T6) magnesium metal matrix composites to enhance mechanical properties and EDM process parameters

EDM Studies on Aluminum Alloy-Silicon Carbide Composites Developed by Vortex Technique and Pressure Die Casting

Synthesis and Characterization of Mechanical Properties and Wire Cut EDM Process Parameters Analysis in AZ61 Magnesium Alloy + B4C + SiC

Experimental Investigations and Optimum Performance Evaluation of Wire-EDM Characteristics of Aluminium 6061-Magnesite Composites

Fabrication and Characterization of Magnesium-Based WE43/TiC Nanocomposite Material Developed via Friction Stir Processing and Study of Significant Parameters

Investigation of Machining Rate and Surface Roughness in Wire EDM of Al6063/WC/ZrO2 Composite using Response Surface Methodology

Experimental investigation, modeling and optimization of wire EDM process parameters for machining AA2024-B4C self-lubricating composite

Experimental investigation of wire electrical discharge machining parameters on WE43 magnesium alloy

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Investigate the mechanical properties of Aluminium Metal Matrix Composite

Characterization of cast rare earth WE43 magnesium alloy and parameter optimization for wire electrical discharge machining using TOPSIS & COPRAS

Experimental examination on electrochemical machining of Mg/FeCoCrNiMn composite

A Hybrid Design of Experiment Approach in Analyzing the Electrical Discharge Machining Influence on Stir Cast Al7075/B4C Metal Matrix Composites

Process parameters optimization of EDM for hybrid aluminum MMC using hybrid optimization technique

Experimental Investigation on Metal Matrix Composite of Abrasive Particles Aided Electrical Discharge Machining

Experimental investigation to assess the surface integrity in WEDM of Al-based hybrid composite material

Mechanical and Tribological Behavior of Mg-Matrix Composites Manufactured by Stir Casting

Investigation of Enhancing EDM Machining Performance of INCONEL Alloy Using Composite Electrodes

An integrated experimental and analytical approach on mechanical characterization of advanced powder metallurgy aluminium metal matrix composites reinforced with different particulates

Experimental Investigation on Metal Matrix Nanocomposite: Aluminium Alloy 6061 and 7075 with SiC and Fly Ash

Study on Powder Mixed EDM of an Aluminium Matrix Composite