Abstract:Purpose: The aim of the proposed research is to establish experimentally the relation between damaging of the tread surface of model wheels and the characteristics of fatigue crack growth resistance of wheel steels "KI th, "KII th, "KI fc, "KII fc), depending on its microstructure. Design/methodology/approach: Characteristics of the fatigue crack growth resistance have been determined on the specimens cut out from the hot rolled plate of thickness 10 mm of the steel which is an analogue of railway wheel steels. To obtain different steel microstructures and its strength level, test specimens were quenched (820°C, in oil) and then tempered at 400°C, 500°C, and 600°C for 2 h. The characteristics of Mode I fatigue crack growth resistance of steel were determined on the basis of fatigue macrocrack growth rate diagrams da/dN–"KI, obtained by the standard method on compact specimens with the thickness of 10 mm at a frequency of 10-15 Hz and the stress ratio R = 0.1 of the loading cycle. The characteristics of Mode II fatigue crack growth resistance were determined on the basis of da/dN–"KII diagrams, obtained by authors method on edge notched specimens with the thickness 3.2 mm at a frequency of 10-15 Hz and R = –1 taking account of the crack face friction. The hardness was measured with a TK-2 hardness meter. Zeiss-EVO40XVP scanning electron microscope was used for microstructural investigations. Rolling contact fatigue testing was carried out on the model specimens of a wheel of thickness 8 mm and diameter 40 mm in contact with a rail of length 220 mm, width 8 mm and height 16 mm. Wheels were manufactured form the above-described steel after different treatment modes. Rails were cut out from a head the full-scale rail of hardness 46 HRC. The damaging was assessed by a ratio of the area with gaps formed by pitting and spalling to the general area of the wheel tread surface using a special stand. Findings: The growth of the damage of the tread surface of the model wheels correlates uniquely with the decrease of the cyclic fracture toughness of the wheel steel "KI fc and "KII fc, determined at Mode I and Mode II fracture mechanisms. These characteristics of the wheel steel can be considered as the determining parameter of this process, in contrast to the fatigue thresholds "KI th and "KII th. Research limitations/implications: Investigations were conducted on model wheels that simulate the damage of real railway wheels tread surface. Practical implications: A relationship between the damage of tread surface of railway wheels and the strength level of wheel steels is determined. Originality/value: The damage of the tread surface of the model wheels during the rolling contact fatigue of the pair wheel-rail increases with the growth of the strength (hardness) of the wheel steel, which corresponds to the statistical data of the operation of the real railway wheels.

INFLUENCE HOT PLASTIC DEFORMATION ON THE STRUCTURE AND PROPERTIES OF CARBON STEEL OF THE RAILWAY WHEEL

STRUCTURAL CHANGES DURING THERMAL STRENGTHENING OF THE RAILWAY WHEEL

Structure and Mechanical Properties of the Heat-Affected Zone of Restored Railway Wheels

Analysis of hardening mechanisms of rail steel under plastic deformation by uniaxial compression

The development of a new deformation regime for microstructure refinement in solid railway axles by hot deformation optimization

Effect of deformation parameters on the austenite dynamic recrystallization behavior of a eutectoid pearlite rail steel

Influence of deformation degree on grains size and borders between them in metal alloys during cold rolling of sheets

Metallurgical aspects of dispersion nitride hardening of high-carbon steel. Message 1. The effect of austenizing heating and tempering parameters on the phase redistribution of nitrogen and vanadium in steels

Relationships between the fatigue crack growth resistance characteristics of a steel and the tread surface damage of railway wheel

Research on Hot Forging Process of C-Grade Steel Train Wheel by Fem

Influence of Microalloying on the Microstructures and Properties of Spalling-Resistant Wheel Steel

Effect of Deformation and Cooling Rate on the Transformation Behavior and Microstructure of X70 Steels

An Alternative Method of Investigating the Thermal Stability of Shoe-Braked Railway Wheel Steels Based on Strain Hardening Analysis

New Method of Severe Plastic Deformation of Metals

Consequences of thermite welding on the microstructure of the heat affected zone of a carbide-free bainitic steel rail

Analysis of compliance of experimental steels for railway rails with modern standards of Ukraine and the EU

Influence of thermal loading parameters and microstructure on the formation of stratified surface layers on railway wheels

EFFECT OF PLASTIC DEFORMATION ON CCT DIAGRAM OF SPRING STEEL 51CrV4

Effect of microstructure on properties of high-power locomotive wheel steels

Influence of hot compressive parameters on flow behaviour and microstructure evolution in a commercial medium carbon micro-alloyed spring steel

CURRENT STATUS AND DEVELOPMENT PROSPECTS OF NANOSTRUCTURING OF DEFORMED METALS AND ALLOYS AND SPRAYED COATINGS