Abstract:Purpose: The aim of the proposed research is to establish experimentally the relation between damaging of the tread surface of model wheels and the characteristics of fatigue crack growth resistance of wheel steels "KI th, "KII th, "KI fc, "KII fc), depending on its microstructure. Design/methodology/approach: Characteristics of the fatigue crack growth resistance have been determined on the specimens cut out from the hot rolled plate of thickness 10 mm of the steel which is an analogue of railway wheel steels. To obtain different steel microstructures and its strength level, test specimens were quenched (820°C, in oil) and then tempered at 400°C, 500°C, and 600°C for 2 h. The characteristics of Mode I fatigue crack growth resistance of steel were determined on the basis of fatigue macrocrack growth rate diagrams da/dN–"KI, obtained by the standard method on compact specimens with the thickness of 10 mm at a frequency of 10-15 Hz and the stress ratio R = 0.1 of the loading cycle. The characteristics of Mode II fatigue crack growth resistance were determined on the basis of da/dN–"KII diagrams, obtained by authors method on edge notched specimens with the thickness 3.2 mm at a frequency of 10-15 Hz and R = –1 taking account of the crack face friction. The hardness was measured with a TK-2 hardness meter. Zeiss-EVO40XVP scanning electron microscope was used for microstructural investigations. Rolling contact fatigue testing was carried out on the model specimens of a wheel of thickness 8 mm and diameter 40 mm in contact with a rail of length 220 mm, width 8 mm and height 16 mm. Wheels were manufactured form the above-described steel after different treatment modes. Rails were cut out from a head the full-scale rail of hardness 46 HRC. The damaging was assessed by a ratio of the area with gaps formed by pitting and spalling to the general area of the wheel tread surface using a special stand. Findings: The growth of the damage of the tread surface of the model wheels correlates uniquely with the decrease of the cyclic fracture toughness of the wheel steel "KI fc and "KII fc, determined at Mode I and Mode II fracture mechanisms. These characteristics of the wheel steel can be considered as the determining parameter of this process, in contrast to the fatigue thresholds "KI th and "KII th. Research limitations/implications: Investigations were conducted on model wheels that simulate the damage of real railway wheels tread surface. Practical implications: A relationship between the damage of tread surface of railway wheels and the strength level of wheel steels is determined. Originality/value: The damage of the tread surface of the model wheels during the rolling contact fatigue of the pair wheel-rail increases with the growth of the strength (hardness) of the wheel steel, which corresponds to the statistical data of the operation of the real railway wheels.

An Alternative Method of Investigating the Thermal Stability of Shoe-Braked Railway Wheel Steels Based on Strain Hardening Analysis

DSI-based Studies of the Effects of High-temperature Aging on Local Mechanical Properties of HR3C/T92 Dissimilar Steel Welded Joint

STRUCTURAL CHANGES DURING THERMAL STRENGTHENING OF THE RAILWAY WHEEL

INFLUENCE HOT PLASTIC DEFORMATION ON THE STRUCTURE AND PROPERTIES OF CARBON STEEL OF THE RAILWAY WHEEL

Evaluation of Thermal Fatigue Life and Crack Morphology in Brake Discs of Low-Alloy Steel for High-Speed Trains

Correlation of microstructure and hardness distribution of high-speed train wheels under original and service statuses

Structure and Mechanical Properties of the Heat-Affected Zone of Restored Railway Wheels

Influence of thermal loading parameters and microstructure on the formation of stratified surface layers on railway wheels

Excellent Wear Resistance of a High-Speed Train Brake Disc Steel with High Hardening Ratcheting Strain Zone

Consequences of thermite welding on the microstructure of the heat affected zone of a carbide-free bainitic steel rail

Relationships between the fatigue crack growth resistance characteristics of a steel and the tread surface damage of railway wheel

Effects of Hot rolling Reduction on Microstructural Evolution and Mechanical Properties of 1.25Cr-1Mo-0.5V-0.3C Steel for High-Speed Rail Brake Discs

Study on the mechanism of mechanical properties deterioration of brake disc materials of high-speed train

Effect of Tempering Temperature on Microstructure and Mechanical Properties of Bainitic Railway Wheel Steel with Thermal Damage Resistance by Alloy Design

Effect of microstructure on wear and rolling contact fatigue behaviors of bainitic/martensitic rail steels

The effects of hardness on the spalling property of railway wheel steel

Detectability of residual stress anomalies in railway wheels with different geometries subjected to thermal overload based on back gauge change

Effect of microstructure on properties of high-power locomotive wheel steels

Characterization of the Microstructure Changes Induced by a Rolling Contact Bench Reproducing Wheel/Rail Contact on a Pearlitic Steel

Assessment of the Hardening Behavior and Tensile Properties of a Cold-Rolled Bainitic-Ferritic Steel

Extended Stress–Strain Characterization of Automotive Steels at Dynamic Rates