Abstract:Understanding and controlling the crystallization process is critical to achieving high‐quality perovskite films and efficient solar cells. Herein, we identified that one key issue in the formation of formamidinium lead iodide (FAPbI3) defects is the participation of the intermediates in the crystallization process. A comprehensive picture of structural and carrier evolution during crystallization was demonstrated using a combination of in situ grazing‐incidence wide‐angle X‐ray scattering, UV‐Vis, and photoluminescence spectroscopies. Three crystallization stages were registered for the commonly observed conversion pathway of precursors – δ‐FAPbI3 intermediate – α‐FAPbI3, during which the spontaneous generation of defects was found. We found that a hydrogen sulfate‐based ionic liquid additive enabled the phase conversion pathway of precursors – solvated intermediates – α‐FAPbI3, during which the spontaneous generation of δ‐FAPbI3 can be effectively circumvented. Both growth kinetics at the initial crystallization stage and the following recrystallization of α‐FAPbI3 were significantly prolonged because of the additional exchange process between solvents and FA+, which resulted in the self‐elimination of defects during crystallization. Therefore, the improved crystallization dynamics led to larger grain sizes and fewer defects within thin films. The improved perovskite crystallization dynamics finally transformed into high‐performance solar cells under one‐sun illumination (AM 1.5 G) with efficiency as high as 25.14% at 300 K. These cells delivered a PCE of 26.12% at 240 K, which might open up a new era of application of this emerging photovoltaic technology to low‐temperature environments such as near‐space and polar regions. This article is protected by copyright. All rights reserved

Terahertz Nanoimaging of the Defects Evolution in Vapor‐Deposited Perovskites Thin‐Film Solar Cell

Defect Passivation in CH3NH3PbI3 Films Using Alkali Metal Fluoride Additives for Highly Efficient Perovskite Solar Cells

Defect Passivation and Electrical Conductivity Enhancement in Perovskite Solar Cells Using Functionalized Graphene Quantum Dots

In situ self‐elimination of defects via controlled perovskite crystallization dynamics for high‐performance solar cells

Direct Observation of Intragrain Defect Elimination in FAPbI 3 Perovskite Solar Cells by Two-Dimensional PEA 2 PbI 4

Synchronous Surface Reconstruction and Defect Passivation for High-Performance Inorganic Perovskite Solar Cells.

Solvent-Free Method for Defect Reduction and Improved Performance of p-i-n Vapor-Deposited Perovskite Solar Cells

Defects in CsPbX3 Perovskite: From Understanding to Effective Manipulation for High-Performance Solar Cells

Direct Observation on p- to n-Type Transformation of Perovskite Surface Region during Defect Passivation Driving High Photovoltaic Efficiency

Surface Defect Passivation and Energy Level Alignment Engineering with a Fluorine-Substituted Hole Transport Material for Efficient Perovskite Solar Cells

Strain Regulation and Defect Passivation of FA‐Based Perovskite Materials for Highly Efficient Solar Cells

Defect Passivation by a Multifunctional Phosphate Additive toward Improvements of Efficiency and Stability of Perovskite Solar Cells

Terahertz Nanoimaging of Perovskite Solar Cell Materials

Multi-Point Collaborative Passivation of Surface Defects for Efficient and Stable Perovskite Solar Cells

Revealing Defect Passivation and Charge Extraction by Ultrafast Spectroscopy in Perovskite Solar Cells through a Multifunctional Lewis Base Additive Approach

Surface Defect Passivation of Pb–Sn‐Alloyed Perovskite Film by 1,3‐Propanediammonium Iodide toward High‐Performance Photovoltaic Devices

Full Defects Passivation Enables 21% Efficiency Perovskite Solar Cells Operating in Air

Defect passivation via incorporation of sodium thiocyanate for achieving high-performance MAPbI3-based perovskite solar cells with enhanced stability

Insight into the Defect Chemistry and Ion Migration in Perovskite Fabricated by Hybrid Chemical Vapor Deposition

In Situ Defect Passivation with Silica Oligomer for Enhanced Performance and Stability of Perovskite Solar Cells

Efficient inorganic vapor‐assisted defects passivation for perovskite solar module