Abstract:The analysis of mechanical response and deformation-cracking behavior contributes to the high-efficiency extraction of geo-energy and long-term safety of underground engineering structures. Compared to natural cores, the mechanical properties of 3D-printed samples made from quartz sand as raw material are relatively homogeneous, and can be used for quantitative studies on the influence of natural defects on the mechanical properties of rocks. In this work, 3D-printed samples with single fractures of different crack angles, lengths and widths were fabricated and used for uniaxial compression tests. Adopting the digital image correlation method, the stress-strain distribution during uniaxial compression tests were visualized, and the influence of prefabricated fracture characteristics (dip angle, length, and width) on the deformation-failure process were studied. An extended finite element method subroutine for ABAQUS® software was modeled and used for the uniaxial compression simulation, which was validated by experiments. Then, the influence of mechanical parameters (Young’s modulus, Poisson’s ratio, cohesion, and internal friction angle) on the deformation-cracking mechanics were simulated and studied. The results indicate that, compared to the intact sample, fractures reduce the sample strength. With the extension of fracture length and width, or the decline of fracture angle, both the peak strain and strength of the 3D-printed samples decrease. The splitting tensile failure, or shear failure, or both were determined for the 3D-printed samples with different fracture angles. For the same axial strain, the extension length of the new crack increases linearly with rising Young’s modulus and decreases linearly with increasing Poisson’s ratio. The initial strain of new cracks decreases linearly with increasing Young’s modulus, while little variations are found in samples with different Poisson’s ratio. For the same axial displacement load, the peak stress increases linearly with growing internal friction angle and cohesion. Cited as: Song, R., Tian, J., Wu, M., Liu, J. Experimental and numerical modeling of deformation-cracking mechanics of 3D-printed rock samples with single fracture. Advances in Geo-Energy Research, 2023, 8(2): 126-135. https://doi.org/10.46690/ager.2023.05.06

Quantification of full-field stress in continuously loaded fractured rocks using 3D printing and digital photoelasticity

Historical shear deformation of rock fractures derived from quantitative three-dimensional description of fracture surfaces on digital outcrop models (DOMs)

Method to quantify the dynamic near-fault full-field stress evolution associated with rough fault shear deformation based on 3D printed models and photoelastic measurements

Method for Visualizing the Shear Process of Rock Joints Using 3D Laser Scanning and 3D Printing Techniques

3D Digital Analysis of Cracking Behaviors of Rocks through 3D Reconstruction Model under Triaxial Compression

Visualization method for stress-field evolution during rapid crack propagation using 3D printing and photoelastic testing techniques

Characterization of stress field evolution during 3D internal fracture propagation using additively printed models and frozen stress techniques

Quantitative description of fracture behavior and mechanical anisotropy of fractured rock mass: Sand 3D printing and DIC explorations

Determination of the Full-Field Stress and Displacement Using Photoelasticity and Sampling Moiré Method in a 3D-Printed Model

Mechanical and Volumetric Fracturing Behaviour of Three-Dimensional Printing Rock-like Samples Under Dynamic Loading

Experimental and numerical modeling of deformation-cracking mechanics of 3D-printed rock samples with single fracture

Experimental method for internal deformation measurement of 3D solids with embedded cracks based on 3D printing and digital speckle techniques

Effect of fractures on mechanical behavior of sand powder 3D printing rock analogue under triaxial compression

Determination of the Stress and Strain Fields in Porous Structures by Photoelasticity and Digital Image Correlation Techniques

Physical reconstruction and mechanical behavior of fractured rock masses

Numerical study on full-field stress evolution and acoustic emission characteristics of rocks containing three parallel pre-existing flaws under uniaxial compression

Simulation of the fracturing process in rocks with flaws using a novel continuous-discontinuous technique

Quantitative Analysis and 3D Visualization of Crack Behavior in 3D-Printed Rock-Like Specimens with Single Flaw Using In-Situ Micro-CT Imaging

Theoretical Study of the Mesoscopic Mechanism of Rock Fractures During Normal Deformation

Intelligent image-based identification and 3-D reconstruction of rock fractures: Implementation and application

Phase-field simulations of unloading failure behaviors in rock and rock-like materials