Abstract:The analysis of mechanical response and deformation-cracking behavior contributes to the high-efficiency extraction of geo-energy and long-term safety of underground engineering structures. Compared to natural cores, the mechanical properties of 3D-printed samples made from quartz sand as raw material are relatively homogeneous, and can be used for quantitative studies on the influence of natural defects on the mechanical properties of rocks. In this work, 3D-printed samples with single fractures of different crack angles, lengths and widths were fabricated and used for uniaxial compression tests. Adopting the digital image correlation method, the stress-strain distribution during uniaxial compression tests were visualized, and the influence of prefabricated fracture characteristics (dip angle, length, and width) on the deformation-failure process were studied. An extended finite element method subroutine for ABAQUS® software was modeled and used for the uniaxial compression simulation, which was validated by experiments. Then, the influence of mechanical parameters (Young’s modulus, Poisson’s ratio, cohesion, and internal friction angle) on the deformation-cracking mechanics were simulated and studied. The results indicate that, compared to the intact sample, fractures reduce the sample strength. With the extension of fracture length and width, or the decline of fracture angle, both the peak strain and strength of the 3D-printed samples decrease. The splitting tensile failure, or shear failure, or both were determined for the 3D-printed samples with different fracture angles. For the same axial strain, the extension length of the new crack increases linearly with rising Young’s modulus and decreases linearly with increasing Poisson’s ratio. The initial strain of new cracks decreases linearly with increasing Young’s modulus, while little variations are found in samples with different Poisson’s ratio. For the same axial displacement load, the peak stress increases linearly with growing internal friction angle and cohesion. Cited as: Song, R., Tian, J., Wu, M., Liu, J. Experimental and numerical modeling of deformation-cracking mechanics of 3D-printed rock samples with single fracture. Advances in Geo-Energy Research, 2023, 8(2): 126-135. https://doi.org/10.46690/ager.2023.05.06

Experimental method for internal deformation measurement of 3D solids with embedded cracks based on 3D printing and digital speckle techniques

Physical Model Test and Application of 3D Printing Rock-Like Specimens to Laminated Rock Tunnels

Estimation of Load-Carrying Capacity of Cracked RC Beams Using 3D Digital Twin Model Integrated with Point Clouds and Images

Method for Visualizing the Shear Process of Rock Joints Using 3D Laser Scanning and 3D Printing Techniques

3D Digital Analysis of Cracking Behaviors of Rocks through 3D Reconstruction Model under Triaxial Compression

Visualization method for stress-field evolution during rapid crack propagation using 3D printing and photoelastic testing techniques

Full-field deformation measurement and cracks detection in speckle scene using the deep learning-aided digital image correlation method

3D meso-scale fracture modelling and validation of concrete based on in-situ X-ray Computed Tomography images using damage plasticity model

Quantitative Analysis and 3D Visualization of Crack Behavior in 3D-Printed Rock-Like Specimens with Single Flaw Using In-Situ Micro-CT Imaging

3D Digital Speckle Analysis System for Dynamic Strain Measurement in Sheet Deformation

Application of the Speckle Technique for Three-Dimensional Deformation Measurement

Quantification of full-field stress in continuously loaded fractured rocks using 3D printing and digital photoelasticity

Measurement of deformations for copper/aluminum clad under tension with digital speckle correlation

3 D In-situ XCT Image Based Mesoscale Fracture Modelling and Validation of Concrete Using Voxel Hexahedron Meshing and Damage Plasticity Model

Experimental and numerical modeling of deformation-cracking mechanics of 3D-printed rock samples with single fracture

Method to Measure 3D Deformation Using Defocused Images of Objects with Artificial Speckle Features

Deformation Fields Measurement of Crack Tip under High-Frequency Resonant Loading Using a Novel Hybrid Image Processing Method

Characterization of stress field evolution during 3D internal fracture propagation using additively printed models and frozen stress techniques

Physical reconstruction and mechanical behavior of fractured rock masses

A novel DIC-based methodology for crack identification in a jointed rock mass

3D Topography of the Micro Cracks of Subsurface Damages by Etching Process