Abstract:The majority of environmental researchers are becoming increasingly concerned with the manufacture of inexpensive adsorbents for the detoxification of industrial effluents. To address one of the significant and well-known pollution issues with certain drains that act as hotspots and contribute to coastal pollution in Alexandria, this study aims to develop an economical, ecologically friendly sorbent. This study assessed the efficacy of a biomass-coated magnetic composite and a magnetic active adsorbent for the removal of two dyes from an industrially contaminated sewer using a wetland plant ( Phragmites australis ). Using magnetic biosorbent, the biosorption of Xylenol orange and Congo red ions from polluted drain discharge in Abu Qir Bay was evaluated in the current study. Using scanning electron microscopy imaging and Fourier transform infra-red analysis; the surface function and morphology of the nano-biosorbent were examined. At room temperature, the effects of initial dye concentration, pH, contact time, and nano-biosorbent concentration have all been investigated. The greatest percentages that nano-biosorbent can remove from Congo red and Xylenol orange are 97% and 47%, respectively. The removal of the initial Congo red concentration varied from 42 to 97%, while the removal of the initial Xylenol orange concentration varied from 30 to 47%. The adsorption capacity was shown to be strongly pH-dependent; capacity dose as pH value increased, with pH 10 being the ideal pH for Congo red and pH 6 being the ideal pH value for Xylenol orange. The adsorption capacity for Congo red varied between 0.96 and 3.36 and the adsorption capacity for Xylenol orange varied between 0.18 and 17.58. The removal capacity decreased from 3.36 to 0.96 mg/g when the biosorbent dosage was increased from 0.05 to 0.5 g/L for Congo red, in case of Xylenol orange, the removal capacity increased from 0.18 to 17.58 mg/g when the biosorbent dosage was increased from 0.05 to 0.5 g/L. The removal capacity of Congo red increases quickly with time and varied from 1.66 to 1.88 of contact time; while the removal capacity of Xylenol orange varied between 3.08 and 4.62 of contact time. For the dyes under study, kinetics and adsorption equilibrium were examined. Within 180 min, the equilibrium was attained because to the quick adsorption process. For Congo red and Xylenol orange, the highest adsorption capacities were 3.36 and 17.58 mg g −1 , respectively. The equilibrium data were assessed using a number of isotherm models, including Langmuir, Freundlich, BET, and Tempkin, while the kinetic data were examined using a variety of kinetic models, including pseudo-first- and pseudo-second-order equations. The pseudo-second-order equation provides the greatest accuracy for the kinetic data and Langmuir model is the closest fit for the equilibrium data.

Modeling of Dispersed Red 17 Dye Removal from Aqueous Solution Using Artificial Neural Network

Intelligent modeling of dye removal by aluminized activated carbon

Remediation of cationic dye from wastewater using a new environmentally friendly adsorbent: A response surface methodology and artificial neural network modeling study

Utilization of factorial design methodology to optimize Pr Red Hegxl dye uptake and prediction of removal efficiency via artificial neural network: comparison of linear vs non-linear sorption isotherm and kinetic parameters

Intelligent modeling of photocatalytically reactive yellow 84 azo dye removal from aqueous solutions by ZnO-light expanded clay aggregate nanoparticles

Artificial Neural Network Modeling of the Removal of Methylene Blue Dye Using Magnetic Clays: An Environmentally Friendly Approach

Artificial neural networks modeling for lead removal from aqueous solutions using iron oxide nanocomposites from bio-waste mass

Biosorption of Acid Black 172 and Congo Red from aqueous solution by nonviable Penicillium YW 01: kinetic study, equilibrium isotherm and artificial neural network modeling.

Adsorptive removal of Direct Red 31 and Direct Orange 26 azo dyes from aqueous solutions using Ficus nano zero valent copper: Linear, non-linear, response surface methodology (RSM), and artificial neural network (ANN) modeling

Polymeric Adsorbent for the Effective Removal of Toxic Dyes from Aqueous Solutions: Equilibrium, Kinetic, and Thermodynamic Modeling

Artificial neural network and genetic algorithms for modeling of removal of an azo dye on walnut husk

Predictive modeling for the adsorptive and photocatalytic removal of phenolic contaminants from water using artificial neural networks

AI-based modeling studies for dye removal using mixed biomass composites from algae and plant seeds: Isotherm, kinetics, and mechanistic insights

Application of response surface methodology for color removing from dyeing effluent using de-oiled activated algal biomass

Molecular simulation-based insights into dye pollutant adsorption: A perspective review

Textural properties and adsorption behaviour of recyclable Ni–Al layered double hydroxides for Congo red and Alizarin red S dyes removal in single and binary systems

Removal of Hazardous Organic Dyes from Liquid Wastes Using Advanced Nanomaterials

Utilization of aquatic biomass as biosorbent for sustainable production of high surface area, nano- microporous, for removing two dyes from wastewater

Modeling and optimization of heterogeneous photo-Fenton process with response surface methodology and artificial neural networks

Sustainable Bio-Based Adsorbents for Simultaneous and Efficient Removal of Hazardous Dyes from Aqueous Solutions

Preparation and potential of chitosan-based/Al2O3 green hydrogel composites for the removal of methyl red dye from simulated solution