Abstract:Clay minerals have large surface areas that contribute to their high adsorption capacity. Pure clays were often used. However, their prices remain expensive. However, the natural clay minerals that are locally available can have economic and environmental benefits for textile wastewater treatment. The tested natural clays had given low removal yields. Therefore, we wanted to test particular rich organic matter clay for adsorbing azo dye, which is a very toxic molecule. In order to make the use of this clay type have a better efficiency for removal of this dye from the polluted waters, the optimal conditions had been specified. The results indicated that advised conditions were as follows: 5 min was the contact time of dye-clay; the better adsorbent masses were 0.25 g and 0.5 g per 100 ml solution for raw (ANb) and purified clays (ANp), respectively; the initial dye concentrations were 1 gL −1 for raw clay and 50 mgL −1 for purified clay; pH solution had any effect on the yield of dye removal only when raw clay was used; however, acid environment was advised when purified clay was the adsorbent and for the two tested clays about 20–30°C was the better solution temperature. X-Ray diffraction, Fourier transform infrared (FTIR) spectroscopy, and scanning electron microscopy (SEM) analysis confirmed that functional groups of clay adsorbed the dye. Langmuir maximum adsorption capacities of ANb and ANp were found to be 397 mgg −1 and 132.3 mgg −1 at pH 7 and 5, respectively. Raw and chemically activated samples gave similar results. Adsorption of ANb and ANp data showed better agreement with the pseudo-second-order kinetic model. Thermodynamic parameters of the two adsorbents confirmed that the adsorption was endothermic (ΔH > 0) and spontaneous (ΔG 0 < 0). Energy level was high when purified clay was used; however, it was significantly lower when the adsorbent was raw clay. Therefore, it was likely that adsorption by carbonates and organic matter involved small energy amounts. Comparing between these and other previous results, Jebel Louka natural clay type is better recommended for MR removal from textile wastewater, since the removal yield was about 98%. Hence, this tested clay type could provide an alternative low-cost material that could be used in treatment of the textile wastewater rich in MR and the obtained adsorption model and desorption tests provided a background for pilot and industrial scale applications.

Intelligent modeling of photocatalytically reactive yellow 84 azo dye removal from aqueous solutions by ZnO-light expanded clay aggregate nanoparticles

Photocatalytic degradation of azo dye using nano-ZrO2/UV/Persulfate: Response surface modeling and optimization

Effective removal of textile dye via synergy of adsorption and photocatalysis over ZnS nanoparticles: Synthesis, modeling, and mechanism

Ni doped zinc oxide nanoparticles supported bentonite clay for photocatalytic degradation of anionic and cationic synthetic dyes in water treatment

Modeling and optimization of heterogeneous photo-Fenton process with response surface methodology and artificial neural networks

Utilization of factorial design methodology to optimize Pr Red Hegxl dye uptake and prediction of removal efficiency via artificial neural network: comparison of linear vs non-linear sorption isotherm and kinetic parameters

Effective adsorption and removal of industrial dye from aqueous solution using mesoporous zinc oxide nanoparticles via metal organic frame work: equilibrium, kinetics and thermodynamic studies

Modeling of Dispersed Red 17 Dye Removal from Aqueous Solution Using Artificial Neural Network

Application of powdered activated carbon coated with zinc oxide nanoparticles prepared using a green synthesis in removal of Reactive Blue 19 and Reactive Black-5: adsorption isotherm and kinetic models

Solar photodegradation of Solophenyl Red 3BL and Neuro-Fuzzy modeling: kinetic, mechanism and mineralization studies

Eco-Friendly Synthesis of ZnO Nanoparticles for Quinoline Dye Photodegradation and Antibacterial Applications Using Advanced Machine Learning Models

Experimental modelling studies on the removal of dyes and heavy metal ions using ZnFe2O4 nanoparticles

Photocatalyzed degradation of acid orange 7 dye under sunlight and ultraviolet irradiation using Ni-doped ZnO nanoparticles

Photocatalytic degradation of an azo reactive dye, Reactive Yellow 84, in water using an industrial titanium dioxide coated media

Removal of Textile Wastewater Pollutants Using Zeolite Mineral as Adsorbent: Isotherm Studies

Modeling of photodegradation process to remove the higher concentration of environmental pollution

Facile synthesis of ZnO nanospheres by co-precipitation method for photocatalytic degradation of azo dyes: optimization via response surface methodology

Efficient photocatalytic remediation of lerui acid brilliant blue dye using radiation- prepared carboxymethyl cellulose/acrylic acid hydrogel supported by ZnO@Ag

Adsorption, Modeling, Thermodynamic, and Kinetic Studies of Methyl Red Removal from Textile-Polluted Water Using Natural and Purified Organic Matter Rich Clays as Low-Cost Adsorbent

Synthesis of MgZnAl Layered Triple Hydroxide Nanoplates as an Efficient Adsorbent for Removing the Acid Yellow 76 Azo Dye

Artificial Neural Network Modeling of the Removal of Methylene Blue Dye Using Magnetic Clays: An Environmentally Friendly Approach