Abstract:Interfacial bonding strength of an epoxy-based adhesive depends on the interfacial interaction between the adhesive and the substrate. Normally, the curing process at the interface accompanied by the interfacial bonding formation is different from that in the bulk, and it is still a big challenge to probe the interfacial bonding formation at a molecular level. In this study, to trace the interfacial structural evolution of a representative formula of epoxy (digylcidyl ether of biphenyl A, DGEBA) and amine hardener [1,2-bis(2-aminoethoxy)ethane, EDDA] with the sapphire and silica substrates upon curing and post-curing steps, sum frequency generation (SFG) vibrational spectroscopy is employed to detect the molecular-level interfacial structural information. For the sapphire substrate, upon curing, backbone methylene (CH2) stretching signals decrease, indicating the formation of a rigid chain network structure and thus losing the local methylene order, while vibrational signals of the sapphire surface hydroxyl (OH) groups (including hydrogen-bonded and unbonded) increase significantly, indicating the formation of a strong hydrogen-bonding and polar interaction between the epoxy adhesive and the sapphire surface. Upon post-curing, increased backbone CH2 signals and decreased sapphire OH signals suggest interfacial chemical bonding formation due to the reaction between the epoxy rings and the sapphire surface OH groups. Orientation analysis confirms the enhanced ordering of the sapphire surface OH groups upon curing and post-curing, in comparison to the uncured epoxy formula. As for the fused silica, weak vibrational signals of the methylene (CH2) and methyl (CH3) groups are observed before curing, while both of them increase slightly for the cured and post-cured epoxy formulae, suggesting relatively less hydrophilic nature of the silica surface compared to that of the sapphire surface, also evidenced by the very weak OH signals upon curing and post-curing. Further measurement on the adhesion strength matches up with the above spectroscopic experimental results, substantiating the correlation between the macroscopic bonding strength of the epoxy adhesive and the microscopic molecular-level structure.

Adhesive Strength Formation of the Epoxy-Anhydride Matrix–Fiber Systems

Molecular Dynamics Simulations of Mechanical Properties of Epoxy-Amine: Cross-linker Type and Degree of Conversion Effects

The Influence of Residual Stresses on the Curve Shape—Describing Interface Behavior in "Polymer–Fiber" Systems

Study of the structure and properties of adhesives and compounds based on epoxy urethane oligomers synthesized from polyesters

Improving Glass Transition Temperature and Toughness of Epoxy Adhesives by a Complex Room-Temperature Curing System by Changing the Stoichiometry

Heat Resistance of Adhesive Joints of Heterocyclic Aramid Fibers under Static Load

Tensile and Shear Creep Behavior of Structural Adhesives: Experiments and Modeling

The Chemical Resistance of Adhesive Bonds Based on Epoxy Urethan Oligomers Synthesized Using Different Diisocyanates

Investigation of Parameters Affecting the Bonding Performance of Carbon Fiber/Epoxy Composites

Preparation And Properties Of Epoxy/Maleimide Compounds And Their Cured Resins

Glass Fiber Reinforced Composites and Thermal Study of Flame Retardant Epoxy Resin Systems Using Anhydride Curing Agents

Asynchronous Ring Opening of Cyclic Carbonate and Glycidyl Ether Induced Phase Evolution Towards Heat‐free and Rapid‐bonding Superior Epoxy Adhesive

Molecular-Level Correlation between Spectral Evidence and Interfacial Bonding Formation for Epoxy Adhesives on Solid Substrates

Effect of post-cure on the glass transition temperature and mechanical properties of epoxy adhesives

Relationship between thermal curing behavior and bond strength development in formaldehyde-based resins with different molecular weights

A STUDY OF THE ADHESIVE AND MATERIAL PROPERTIES OF AN EPOXY RESIN FORMULATION AS A FUNCTION OF PROPORTIONING THE INGREDIENTS: PART II

Studies on Phase Separation of Polyesterimide-Modified Epoxy Resin. Ii. Effect of Curing Temperature on Phase Separation and Adhesive Property

The effect of epoxy resin and curing agent groups on mechanical properties investigated by molecular dynamics

Study of Adhesive Used for Strengthening Concrete Structure with FRP-Part 2 Impregnated Resin

Characterization of thermosetting epoxy modified asphalt adhesives

Effect of curing agents n‐octylamine and m‐xylene diamine on the mechanical and memory properties of E51 epoxy resin