Abstract:Hydrogels consist of crosslinked hydrophilic polymers from which their mechanical properties can be modulated for a wide variety of applications. In the last decade, many catechol-based bioinspired adhesives have been developed following the strategy of incorporating catechol moieties into polymeric backbones. In this work, in order to further investigate the adhesive properties of hydrogels and their potential advantages, several hydrogels based on poly(2-hydroxyethyl methacrylate-co-acrylamide) with N′N-methylene-bisacrylamide (MBA), without/with L-3,4-dihydroxyphenylalanine (DOPA) as a catecholic crosslinker, were prepared via free radical copolymerization. 2-Hydroxyethyl methacrylate (HEMA) and acrylamide (AAm) were used as comonomers and MBA and DOPA both as crosslinking agents at 0.1, 0.3, and 0.5 mol.-%, respectively. The polymeric hydrogels were characterized by Fourier transform infrared spectroscopy (FT-IR), thermal analysis and swelling behavior analysis. Subsequently, the mechanical properties of hydrogels were determined. The elastic properties of the hydrogels were quantified using Young's modulus (stress–strain curves). According to the results herein, the hydrogel with a feed monomer ratio of 1:1 at 0.3 mol.-% of MBA and DOPA displayed the highest rigidity and higher failure shear stress (greater adhesive properties). In addition, the fracture lap shear strength of the biomimetic polymeric hydrogel was eight times higher than the initial one (only containing MBA); however at 0.5 mol.-% MBA/DOPA, it was only two times higher. It is understood that when two polymer surfaces are brought into close contact, physical self-bonding (Van der Waals forces) at the interface may occur in an –OH interaction with wet contacting surfaces. The hydrogels with DOPA provided an enhancement in the flexibility compared to unmodified hydrogels, alongside reduced swelling behavior on the biomimetic hydrogels. This approach expands the possible applications of hydrogels as adhesive materials, in wet conditions, within scaffolds that are commonly used as biomaterials in cartilage tissue engineering.

Study of the structure and properties of adhesives and compounds based on epoxy urethane oligomers synthesized from polyesters

Studies on the influence of soft-segment structure on the properties of polyurethane adhesive

Synthesis of Thermally Degradable Epoxy Adhesives

Synthesis and properties of poly(acrylates-co-urethane) adhesives for low surface energy materials

The Chemical Resistance of Adhesive Bonds Based on Epoxy Urethan Oligomers Synthesized Using Different Diisocyanates

Development and Study of a New Silane Based Polyurethane Hybrid Flexible Adhesive-Part 1: Mechanical Characterization

Influence of polyoxypropylenetriamin and content of oxirane rings on properties of epoxy-polysulfide composites

Synthesis of Reactive Polyurethane Adhesives and Studying the Effect of Ketonic Resins

Preparation and Properties of Advanced Materials for Bi-component Polyurethane Adhesives Containing Siloxane.

Hydrogen bonding in polyurethane elastomers based on 1,5-naphthalene diisocyanate

Adhesive and Impact-Peel Strength Improvement of Epoxy Resins Modified with Mono and Diamine Functionalized Elastomers

Polyurethane Adhesives with Chemically Debondable Properties via Diels-Alder Bonds

Synthesis and mechanical properties of epoxy resin adhesive toughened by liquid polysulfide polyurea

Study on Preparation and Performance of Reactive Polyurethane Hot Melt Adhesives Based on a Polycarbonate Diol and a Polyester Diol

The synthesis and characterization of supramolecular elastomers based on linear carboxyl-terminated polydimethylsiloxane oligomers

Facile synthesis of polyester-polyether block copolyols for the sustainable high-performance polyurethane reactive hot melt adhesives

Study on preparation and properties of a thermally removable epoxy resin adhesive

Synthesis, Characterization and Catechol-Based Bioinspired Adhesive Properties in Wet Medium of Poly(2-Hydroxyethyl Methacrylate-co-Acrylamide) Hydrogels

Influence of concentration of thiokol, amount of the hardener and filler on properties of epoxide-polysulphide composites

Design, Preparation and Characterization of a High-Performance Epoxy Adhesive with Poly (Butylacrylate-block-styrene) Block Copolymer and Zirconia Nano Particles in Aluminum- Aluminum Bonded Joints

Castor oil-based polyurethane adhesives: Effect of cross-linker on the bond strength