Abstract:The geometric parameters and stress conditions of fractures are the main factors that determine the strength and deformation characteristics of fractured rock masses, and the ultimate instability and failure of fractured rock masses are caused by the extension and penetration of the structural plane. In this study, a series of Φ50 × 100 mm standard cylinder specimens were prepared to simulate brittle rock masses. The uniaxial compressive strength and tensile strength of the specimens were 33 and 2.8 MPa, respectively. Non-persistent fractures with different inclination angles, connectivity rates, openings, spacings, groups, and roughness were prefabricated in the specimens, and the fractures were filled with plasticine. Furthermore, the crack propagation and failure mechanisms of filled fractured rock masses under uniaxial compression (the loading rate is 0.2 MPa/s) were analyzed by a 3D video image correlation system. Comparing the results of this research with those of previous researches, and combining with relevant theoretical analysis, the following conclusions are drawn: (1) the curve of the peak strength reduction coefficient k σ of the specimen with the fracture inclination angle α is roughly V-shaped, and being the smallest when the fracture inclination angle α is 45°; the reduction coefficient k is monotonically decreasing with the three groups of fracture geometric parameters of spacing b , connectivity rate μ , and opening d , and the peak strength reduction coefficient k σ of the specimen is typically smaller than the elastic modulus reduction coefficient k E . (2) The post-peak stress–strain curve of the specimen with filled fractures is relatively slow, and the plasticity is obviously enhanced. The geometric parameters of the fractures are important factors affecting the change of the mechanical properties of the specimen. The influence degree of different fractures geometric parameters on rock masses mechanical properties is as follows: fracture sets > spacing > connectivity rate > inclination angle > opening > roughness. (3) Due to the concentration of stress, cracks first initiate from the fracture tips, then propagate parallel to the loading direction, and ultimately coalesce between the fractures and the specimen surface. During the failure process of the specimens, four types of cracks were observed: tensile cracks, shear cracks, wing cracks, and reverse wing cracks, with wing cracks dominating crack propagation. (4) Compared with the specimens with unfilled fractures, the stress concentration at the filled fractures was reduced, and more microcracks with higher dispersion developed around the filled fracture.

Multiscale fracture characteristics and failure mechanism quantification method of cracked rock under true triaxial compression

Study on multi-scale damage and failure mechanism of rock fracture penetration: experimental and numerical analysis

3D Digital Analysis of Cracking Behaviors of Rocks through 3D Reconstruction Model under Triaxial Compression

Experimental Study on Uniaxial Compression Mechanics and Failure Characteristics of Non-Through Fractured Rock

Mechanical Behavior and Fracture Characteristics of Rock with Prefabricated Crack under Different Triaxial Stress Conditions

Study on Macro–Meso Failure Mechanism of Pre-fractured Rock Specimens Under Uniaxial Compression

Research on meso-scale deformation and failure mechanism of fractured rock mass subject to biaxial compression

Research on crack initiation mechanism and fracture criterion of rock-type materials under compression–shear stress

Study on the evolution law and quantitative characterization of micro-crack propagation in the compressive failure process of rocks

A True Triaxial Compression-Induced Microcracking Model for Evaluating Short-Term Progressive and Long-Term Creep Failures of Brittle Rock

Crack propagation process and acoustic emission characteristics of rock-like specimens with double parallel flaws under uniaxial compression

Experimental and numerical simulation study of crack coalescence modes and microcrack propagation law of fissured sandstone under uniaxial compression

Experimental and numerical studies of brittle rock-like specimens with unfilled cross fissures under uniaxial compression

A Micro–macro Method for Evaluating Progressive and Direct Tensile Fractures in Brittle Rocks

Mechanical behavior and tension-shear failure mechanism of fractured rock mass under uniaxial condition

Investigation of Microcrack Propagation and Energy Evolution in Brittle Rocks Based on the Voronoi Model

Numerical Study on Cracking Behavior and Fracture Failure Mechanism of Flawed Rock Materials under Uniaxial Compression

Experimental and numerical investigation on the mechanical responses and cracking mechanism of 3D confined single-flawed rocks under dynamic loading

Experimental Study on Mechanical Behavior, Fracture Characteristics, and Acoustic Emission Damage Characteristics of Sandstone Under Triaxial Multistage Stress Disturbance

Experimental Study on the Effects of Geometric Parameters of Filled Fractures on the Mechanical Properties and Crack Propagation Mechanisms of Rock Masses

Numerical Study of Failure Behaviour of Pre-Cracked Rock Specimens under Conventional Triaxial Compression