Abstract:Abstract The field under study is located in the northern part of Oman where most of the fields have a tight carbonate oil reservoirs. Initially the field was produced under natural depletion for almost 15 years until 2005 when a line drive water flood development with horizontal wells took place and was deployed in the whole field. After more than 10 years of water injection, the water cut reached an average of 75% in the major producing blocks. The reservoir has a light oil with viscosity of 0.8 mPa.s, a downhole temperature of 87°C and average permeability of 10 mD. The calcium and magnesium concentration in formation water is high, about 4000 mg/L. Reservoir heterogeneity in tight carbonate reservoirs causes uneven water flood sweep efficiency and hence resulted in a lot of bypassed oil. The initial EOR methods screening in the field under study didn't recommend to use the conventional polymer flooding due to low reservoir permeability and hence injectivity challenge. However, a new unique nano-ploymer was recently developed in the market to be a potential EOR method for such tight formation reservoirs. Extensive laboratory experiments using the core and fluid samples from the studied reservoir followed by numerical simulation modeling work proved the technical feasibility for this new polymer. This was then followed by field testing pilot in one of the matured water flood sector and the performance is currently under monitoring. The new polymer is a particle-type and comes with various nanometer-micrometer sizes. This polymer has a low apparent viscosity of 1-4 mPa and when it is mixed with the injection water, the particles disperse in the water and the resultant mixture has a low viscosity making it easily to be injected. In addition, this nano-polymer has a high tolerance for both temperature and salinity. While the particles move into formation, they temporarily plug the preferential existing water paths and divert the injection water into the relatively small pores/throats and displace the remaining bypassed oil. The polymer particle has high deformation capacity, so it can deform and pass through the throat under certain pressure to plug even deeper parts of the formation. The process is repeated continuously so that it can inhibit water production and enhance oil production. For the lab experiments, 12 core plugs from the associated reservoir were collected, based on which, a series of experiments were conducted including: core thin section analysis, injectivity test for the nano-polymer and core flooding experiments on single plug and parallel double plugs. Subsequently, the lab results were utilized for numerical simulation and that was followed by economic evaluation. Based on the lab test results, a conceptual simulation model for the studiedfield's sector was used to estimate the incremental oil gain at different pore volume (PV) injection. The incremental oil gain was determined at different SMG PV injection starting from 0.05PV to 0.5 PV. The results showed that the best economic scenario is to go for PV injection of 0.3 which can be achieved in ~4 years'time. However, in order to expedite the field trail stage and reduce its cost, the lowest PV injection was selected which involves injection in two water injectors for one year only at 0.05 PV. The field pilot thus far has successfully completed the injection phase of the total planned volume (0.05 PV) of nano-ploymer. The injection was continuous for one year with no injectivity issue and the production performance is currently under monitoring.

Chemical-Enhanced Oil Recovery by Alkali/Sulfate Smart Water Flooding in Carbonate Reservoirs Using a Green Polymer Extracted from Plantago ovata Seed

Next-Generation Gelling Agents for Improved Displacement in Enhanced Oil Recovery Processes

Smart Nanoparticles for Conformance Improvement in Waterflooding

Next-Generation Displacement Fluids for Enhanced Oil Recovery

Experimental Study on the Application of Cellulosic Biopolymer for Enhanced Oil Recovery in Carbonate Cores under Harsh Conditions

Optimizing the Performance of Produced Water Chemical Treatment Following CEOR Polymer Breakthrough

Guar Gum-Based Hydrogels as Potent Green Polymers for Enhanced Oil Recovery in High-Salinity Reservoirs

Synthesis and viscometric behavior of a novel associative polymer for enhanced oil recovery

Chemical Enhanced Oil Recovery and Viscose Flooding into Sandstone Reservoirs Using a Natural Polymer Extracted from Sucrose‐Rich Waste by Bacterial Activity

Enhanced Oil Recovery Using Polymer Alternating CO 2 Gas Injection: Mechanisms, Efficiency, and Environmental Benefits

A New Polymer Flooding Technology for Improving Low Permeability Carbonate Reservoir Recovery--From Lab Study to Pilot Test--Case Study from Oman

Experimental Investigation of a Mechanically Stable and Temperature/Salinity Tolerant Biopolymer toward Enhanced Oil Recovery Application in Harsh Condition Reservoirs

Synergistic Effect of Opuntia ficus-indica Cladode mucilage on Physicochemical and Rheological properties of HPAM polymer solutions for EOR Application

Impact on Corrosion of Different Types of EOR Polyacrylamides in Various Conditions of Salinity and Temperature

Investigation of EOR Formulations with Engineered Brines Utilizing Bespoke Polymer for a Candidate Offshore Heterogeneous Sandstone Reservoir

Low-Salinity Polymer Flood for Enhanced Oil Recovery in Low-Permeability Carbonates

A New Logistically Simple Solution for Implementing Alkali-Surfactant-Polymer/Alkali-Cosolvent-Polymer in Difficult Environments: Evaluation of Concept with High Total Acid Number Viscous Crude Oil

Comparative Study on Enhancing Oil Recovery under High Temperature and High Salinity: Polysaccharides Versus Synthetic Polymer

Application of Water-Soluble Polymer/Biopolymer Combined with a Biosurfactant in Oil-Wet Fractured Carbonate Reservoirs

Study on interfacial tension, wettability and viscosity in different salinities of synthesized a new polymeric surfactant for improving oil recovery

Influence of suspended microcrystalline polymer system on characteristics of produced water from High Ca and Mg oilfields and corresponding oil removal methods