Abstract:Abstract The field under study is located in the northern part of Oman where most of the fields have a tight carbonate oil reservoirs. Initially the field was produced under natural depletion for almost 15 years until 2005 when a line drive water flood development with horizontal wells took place and was deployed in the whole field. After more than 10 years of water injection, the water cut reached an average of 75% in the major producing blocks. The reservoir has a light oil with viscosity of 0.8 mPa.s, a downhole temperature of 87°C and average permeability of 10 mD. The calcium and magnesium concentration in formation water is high, about 4000 mg/L. Reservoir heterogeneity in tight carbonate reservoirs causes uneven water flood sweep efficiency and hence resulted in a lot of bypassed oil. The initial EOR methods screening in the field under study didn't recommend to use the conventional polymer flooding due to low reservoir permeability and hence injectivity challenge. However, a new unique nano-ploymer was recently developed in the market to be a potential EOR method for such tight formation reservoirs. Extensive laboratory experiments using the core and fluid samples from the studied reservoir followed by numerical simulation modeling work proved the technical feasibility for this new polymer. This was then followed by field testing pilot in one of the matured water flood sector and the performance is currently under monitoring. The new polymer is a particle-type and comes with various nanometer-micrometer sizes. This polymer has a low apparent viscosity of 1-4 mPa and when it is mixed with the injection water, the particles disperse in the water and the resultant mixture has a low viscosity making it easily to be injected. In addition, this nano-polymer has a high tolerance for both temperature and salinity. While the particles move into formation, they temporarily plug the preferential existing water paths and divert the injection water into the relatively small pores/throats and displace the remaining bypassed oil. The polymer particle has high deformation capacity, so it can deform and pass through the throat under certain pressure to plug even deeper parts of the formation. The process is repeated continuously so that it can inhibit water production and enhance oil production. For the lab experiments, 12 core plugs from the associated reservoir were collected, based on which, a series of experiments were conducted including: core thin section analysis, injectivity test for the nano-polymer and core flooding experiments on single plug and parallel double plugs. Subsequently, the lab results were utilized for numerical simulation and that was followed by economic evaluation. Based on the lab test results, a conceptual simulation model for the studiedfield's sector was used to estimate the incremental oil gain at different pore volume (PV) injection. The incremental oil gain was determined at different SMG PV injection starting from 0.05PV to 0.5 PV. The results showed that the best economic scenario is to go for PV injection of 0.3 which can be achieved in ~4 years'time. However, in order to expedite the field trail stage and reduce its cost, the lowest PV injection was selected which involves injection in two water injectors for one year only at 0.05 PV. The field pilot thus far has successfully completed the injection phase of the total planned volume (0.05 PV) of nano-ploymer. The injection was continuous for one year with no injectivity issue and the production performance is currently under monitoring.

Enhanced Oil Recovery Using Polymer Alternating CO 2 Gas Injection: Mechanisms, Efficiency, and Environmental Benefits

Next-Generation Displacement Fluids for Enhanced Oil Recovery

Production Optimization under Injection of Biopolymer, Synthetic Polymer and Gels in a Heterogeneous Reservoir

Polymer-Assisted WAG Injection Improves CO2 Flow Properties in Porous Media

Investigation of Polymer-Assisted CO2 Flooding to Enhance Oil Recovery in Low-Permeability Reservoirs

Pore-scale characterization of carbon dioxide storage at immiscible and near-miscible conditions in altered-wettability reservoir rocks

CO2 Foam and CO2 Polymer Enhanced Foam for Heavy Oil Recovery and CO2 Storage

Numerical Investigation on Alkaline-Surfactant-Polymer Alternating CO2 Flooding

Influence of EOR Polymers on Fouling in Production Wells and Facilities

A New Polymer Flooding Technology for Improving Low Permeability Carbonate Reservoir Recovery--From Lab Study to Pilot Test--Case Study from Oman

Chemical-Assisted CO2 Water-Alternating-Gas Injection for Enhanced Sweep Efficiency in CO2-EOR

An experimental investigation of liquid CO2-in-water emulsions for improving oil recovery

Potential of Associative Polymers as Mobility Control Agents in Low Permeability Carbonates

New Insights into Geochemical Modeling of Hybrid Low Salinity/Engineered Water and Polymer Injections in Carbonates

Experimental Study on Enhanced Oil Recovery of the Heterogeneous System after Polymer Flooding

Polymer viscosifier systems with potential application for enhanced oil recovery: a review

A Review of Polymer Gel Utilization in Carbon Dioxide Flow Control at the Core and Field Scale

Multiphase flow characteristics and EOR mechanism of immiscible CO2 water-alternating-gas injection after continuous CO2 injection: A micro-scale visual investigation

Experimental Study on the Application of Cellulosic Biopolymer for Enhanced Oil Recovery in Carbonate Cores under Harsh Conditions

Chemical-Enhanced Oil Recovery by Alkali/Sulfate Smart Water Flooding in Carbonate Reservoirs Using a Green Polymer Extracted from Plantago ovata Seed

Hybrid Engineered Water–Polymer Flooding in Carbonates: A Review of Mechanisms and Case Studies