Abstract:In this study, we conducted indoor temporary plugging and diverting fracturing (TPDF) experiments on samples of natural deep and shallow coal seams using a small-scale true triaxial fracturing simulation system. By integrating high-precision CT scanning technology and crack reconstruction techniques, and relying on the quantitative characterization of the crack complexity coefficient, we investigated the differences in internal structures between deep and shallow coal seam samples and the variations in the expansion of TPDF cracks. Furthermore, the study primarily focused on exploring the influence of temporary plugging agent (TPA) parameters (quantity and particle size) on the expansion patterns of TPDF cracks in deep coal seam coal-rock samples. The experimental results reveal that in shallow coal samples, artificially induced fractures are notably longer and extend to various surfaces of the samples. Conversely, in deep coal samples, the expansion of artificially induced fractures is influenced by well-developed cleavage and cleats. The crack complexity coefficient of artificial fractures in deep coal samples is 1.54 higher than that in shallow coal samples, with an increased crack width of 98 μm. However, the expansion distance of the fractures is shorter and does not extend to the S3 and S6 surfaces. Increasing the dosage of the TPA is advantageous for inducing frequent redirection of fractures and communication with previously untouched areas. When the dosage of the TPA is increased from 30 g/L to 60 g/L, the expansion distance of artificial fractures significantly increases, extending to various surfaces of the samples. The crack complexity coefficient increases by 1.1, and the crack width enlarges by 84 μm. Appropriate particle sizes of the TPA can effectively form seals. However, small particle sizes (200/400 mesh) struggle to seal initial fractures, while large particle sizes (10/20 mesh) can lead to excessive wellhead blockage, causing rapid shut-in pressure, destructive fracturing in deep coal samples, and the generation of a large amount of coal fines. This study holds significant guidance for the optimal selection of process parameters in the temporary plugging hydraulic fracturing of deep coal rock.

Technology of injection isolation of coal mine workings

Performance Research of Materials and Engineering Application of Overburden Strata Separation-Zone Grouting Technology

Physical simulation study on grouting water plugging of flexible isolation layer in coal seam mining

Synchrotron X-ray Tomographic Characterization of Microstructural Evolution in Coal Due to Supercritical CO2 Injection at In-Situ Conditions

Mineral Injection Mixtures for Construction and Operation of Underground Structures under Dense Urban Development Conditions

Investigation into hydraulic fracture propagation behavior during temporary plugging and diverting fracturing in deep coal seam

Test on Water-Level Stabilization and Prevention of Mine-Shaft Failure by Means of Groundwater Injection

Optimization and Application of Water Injection Process in Gas-Bearing Coal Seam

Effects of Injection Pressure and Duration on Alternate High-Pressure Water-Gas Sequestration of Coalbed Methane

A Feasibility Study of Coal Seam Water Injection Processes: The Effects of Coal Porosity and Mass Flow Rates of Injected Water on Wetting Radii

Mechanism of and Prevention Technology for Water Inrush from Coal Seam Floor under Complex Structural Conditions—A Case Study of the Chensilou Mine

Study on the infiltration mechanism of injecting chelating agent into deep low permeable coal seam

Numerical Simulation of Combined Water Injection in Deep Coal Seam and Its Field Application for Dust Suppression and De-stressing: A Case Study at Dongtan Coal Mine, China

A small-scale experimental study of CO2 enhanced injectivity methods of the high-rank coal

Investigation into Hydraulic Fracture Propagation Behavior during Temporary Plugging and Diverting Fracturing in Coal Seam

Diffusion Mechanism of Slurry during Grouting in a Fractured Aquifer: A Case Study in Chensilou Coal Mine, China

Time Effect of Water Injection on the Mechanical Properties of Coal and Its Application in Rockburst Prevention in Mining

A Novel In-Seam Borehole Discontinuous Hydraulic Flushing Technology in the Driving Face of Soft Coal Seams: Enhanced Gas Extraction Mechanism and Field Application

Laboratory Study of Deformation Behaviour of Two New Reinforcing Polymeric TSLs and Their Potential Application in Deep Underground Coal Mine

Stress Relief and Permeability Enhancement with Hydraulic Fracturing in Overlying Key Strata of Deep and Soft Coal Seams

Experimental Research of Simultaneous Water and Gas Injection Technology into Injection Wells using Mixing Devices