Abstract:The techniques for releasing thermal energy accumulated in periods of high availability to meet the demand in periods of low energy supply contribute to the continuity of the cycles involved in thermodynamic processes. In this context, phase change materials are capable of absorbing and releasing large amounts of energy in relatively short periods of time and under specific operating conditions. However, phase change materials have low thermal conductivity and need to be coupled with high-thermal-conductivity materials so that the heat flux can be intensified and the energy absorption and release times can be controlled. This work aims to numerically study the solidification process of a phase change material inserted into a triplex tube heat exchanger with finned copper walls to intensify the thermal exchange between the phase change material and the cooling heat transfer fluid, water, that will receive the energy accumulated in the material. This work proposes the 3D numerical modeling of the triplex tube heat exchanger with finned walls and meets the need for numerical models that allow for the analysis of the full geometry of the latent heat thermal energy storage system and the thermal and fluid dynamic phenomena that are influenced by this geometry. Results of the temperature, liquid fractions and velocity fields during phase transformations are presented, analyzed and validated with experimental data, presenting average errors of below 5%. The total material discharge time was approximately 168 min, necessary for the complete solidification of the phase change material, with water injected into the triplex tube heat exchanger at a flow rate of 8.3 L/min and a temperature of 68 °C. The solidification process occurred more slowly in the same direction as the length of the triplex tube heat exchanger, and from 80% of the material in the solid state, the difference between the solidification time for z = 0 and z = 480 mm was 30 min. The fluid dynamic conditions developed in the latent heat thermal energy storage system promoted a maximum negative heat flux of −6423 w/m2 to the annular internal surface and −742 w/m2 to the annular external surface, representing a heat removal process nine times less intense on the external surface. The total energy released to the cooling heat transfer fluid was 239.56 kJ/kg.

Numerical study of melting and solidification behavior of radial and linear cascaded metal foam latent heat storage shell and tube heat exchanger

Numerical Investigation of Heat Transfer Characteristics in a Shell- And-Tube Latent Heat Thermal Energy Storage System

Optimisation of a hybrid latent heat storage unit based on phase change time and exergy efficiency

A novel numerical study on the melting process of phase change materials in a heat exchanger for energy storage

CFD Analysis of Latent Heat Energy Storage System with Different Geometric Configurations and Flow Conditions

Prediction of transient melt fraction in metal foam - nanoparticle enhanced PCM hybrid shell and tube heat exchanger: A machine learning approach

Numerical investigation on thermal performance of phase change materials embedded in functionally graded metal foam

Numerical Analysis on a Latent Thermal Energy Storage System with Phase Change Materials and Aluminum Foam

Experimental and numerical investigation of the melting behavior of a phase change material in a horizontal latent heat accumulator with longitudinal and annular fins

Experimental and Numerical Studies on Melting/solidification of PCM in a Horizontal Tank Filled with Graded Metal Foam

Numerical simulation on thermal behavior of partially filled metal foam composite phase change materials

Numerical thermal performance assessment of phase change process in a PCM/foam-fins enclosure under various thermal conditions

Heat transfer analysis during the solidification of RT82 paraffin in big-scale metal foam-based latent thermal storage unit

Numerical investigation on thermal behaviors of two-dimensional latent thermal energy storage with PCM and aluminum foam

NUMERICAL STUDY OF THE GEOMETRIC INFLUENCE OF A FIN IN A CYLINDRICAL HEAT EXCHANGER FOR MELTING OF PCM

Numerical study of the melting rate enhancement of nano phase change material in a modified shell and tube heat exchanger

Numerical Study of Thermal Conductivity Effect on The Performance of Thermal Energy Storage

Computational study on transient thermal performance enhancement of phase change materials in triplex tube heat exchanger through novel annular-finned configurations

Numerical study on latent heat thermal energy storage with phase change material and metal foam in shell and corrugated tube with external heat losses

Design and study of metal foam parameters on whole melting-solidification cycle in phase change heat storage system

3D Numerical Analysis of a Phase Change Material Solidification Process Applied to a Latent Thermal Energy Storage System