Abstract:Effective thermal management is key to ensuring the reliable operation of high power electronic equipment. In this study, the strategy of phase transition and liquid cooling coupling applied to transient high power electronic equipment has been examined. In order to improve the performance of the phase changing material (PCM) in temperature control, the effects of the coupling structure have been addressed with a consideration of fin, copper foam (CF), graphite foam (GF), fin-copper foam (FCF) and fin-graphite foam (FGF) structures in heat dissipation. In this study, pure paraffin wax (PPW) was used as phase change material to prepare heat sinks based on the above five structures. The experimental study investigates the impact of different thermal conductivity strategies on temperature control characteristics, with a focus on cold capacity recovery and the combined phase change and liquid cooling, using pure paraffin wax module as a reference. The results have revealed that the fin-foam coupling structure delivers a better PCM performance than the single fin or foam structure. Operating at a heating power of 10 W, 15 W and 20 W, the temperature control time of the FGF structure was increased by 13.6 %∼14.6 % relative to the GF structure. At 15 °C with flow rates of 1 L/min, 1.5 L/min, 2 L/min liquid cooling conditions, the cooling capacity recovery time was reduced by 18.8 %, 17.2 %, 19.7 %, respectively. In the phase-change liquid-cooling coupling temperature control experiment, the final temperature increase in the FGF system was 11.7 °C -15.2 °C lower than that of the GF system under the same water temperature and volume flow for a 50 W heat source. The incorporation of fins also enhanced the thermal conductivity strengthening capability of the copper foam and reduced the cold recovery time. Based on the comprehensive evaluation, the FGF structure demonstrates superior temperature control performance and cold recovery characteristics of PCM, making it an optimal strengthening method. Following closely are the FCF, GF, Fin and CF structures. Compared to pure paraffin modules, these five modules exhibit varying degrees of improvement in temperature control and cold capacity recovery efficiency. This study provides guidance for optimizing heat sink design based on PCM in electronic applications.

Numerical thermal performance assessment of phase change process in a PCM/foam-fins enclosure under various thermal conditions

Transient Performance of a PCM-based Heat Sink with a Partially Filled Metal Foam: Effects of the Filling Height Ratio

Performance Evaluation and Analysis of a Vertical Heat Pipe Latent Thermal Energy Storage System with Fins-Copper Foam Combination

Numerical simulation on thermal behavior of partially filled metal foam composite phase change materials

Influence of the Copper Foam Fin (CFF) shapes on thermal performance of Phase-Change Material (PCM) in an enclosed cavity

Experimental and numerical investigation of the melting behavior of a phase change material in a horizontal latent heat accumulator with longitudinal and annular fins

Impact of using different numbers of fins on heat transfer augmentation in a phase-change material helical coil latent energy storage system

Numerical investigation on thermal performance of phase change materials embedded in functionally graded metal foam

Numerical simulation of thermal performance of heat sink augmented with phase change material PCM integrated with solid and aluminum metal foam fins

Numerical investigation on thermal behaviors of two-dimensional latent thermal energy storage with PCM and aluminum foam

Influence of the foam-fin structure on the thermal performance of a coupled phase change liquid cooling module

Numerical Analysis on a Latent Thermal Energy Storage System with Phase Change Materials and Aluminum Foam

How can copper foam better promote the melting process of phase change materials

Computational study of a latent heat thermal energy storage system enhanced by highly conductive metal foams and heat pipes

Numerical study on heat transfer enhancement of PCM using three combined methods based on heat pipe

Performance improvement of phase change material (PCM)-based shell-and-tube-type latent heat energy storage system utilizing curved fins

Improving the melting performance of phase change material (PCM) in a latent heat thermal energy storage unit via a non-uniform arrangement of longitudinal fin

Numerical study on the thermal performance of foam-metal composite phase change material in different force fields

Experimental study of heat transfer enhancement using metal foam partially filled with phase change material in a heat sink

Heat transfer analysis of phase change material composited with metal foam-fin hybrid structure in inclination container by numerical simulation and artificial neural network

Heat transfer enhancement of nano-encapsulated phase change material (NEPCM) using metal foam for thermal energy storage