Abstract:Abstract Metal-composite laminates and joints are applied in aircraft manufacturing and maintenance (repairing) using aluminum alloys (AA) and glass fiber-reinforced polymer (GFRP). In these applications, drilling has a prominent place due to its vast application in aeronautical structures’ mechanical joints. Thus, this study presents the influence of uncoated carbide drills (85C, 86C, H10N), cutting speeds ( v c = 20, 40, and 60 m min −1 ), and feed rates ( f = 0.05, 0.15, and 0.25 mm rev −1 ) on delamination factor, thrust force ( F t {F}_{\text{t}} ), and burr formation in dry drilling metal-composite laminates and joints (AA2024/GFRP/AA2024). Experiments were performed, analyzed, and optimized using the Box–Behnken statistical design. Microscopic digital images for delamination evaluation, piezoelectric dynamometer for thrust force acquisition, and burr analysis were considered. The major finding was that the thrust force during drilling depends significantly on the feed rate. Another significant factor was the influence of the drill type (combined or not with feed rate). In fact, it was verified that the feed rate and the drill type were the most significant parameters on the delamination factor, while the feed rate was the most relevant on thrust force. The cutting speed did not affect significantly thrust force and delamination factor at exit ( F da S ) \hspace{.25em}({F}_{{\text{da}}_{\text{S}}}) . However, the combination f × v c was significant in delamination factor at entrance ( F da E ) \text{ }({F}_{{\text{da}}_{\text{E}}}) . Based on the optimized input parameters, they presented lower values for delamination factors ( F da E = 1.18 {F}_{{\text{da}}_{\text{E}}}=1.18 and F da S = 1.33 {F}_{{\text{da}}_{\text{S}}}=\hspace{.25em}1.33 ) and thrust force ( F t = 67.3 N {F}_{\text{t}}=67.3\hspace{.5em}\text{N} ). These values were obtained by drilling the metal-composite laminates with 85C-tool, 0.05 mm rev −1 feed rate, and 20 m min −1 cutting speed. However, the burrs at the hole output of AA2024 were considered unsatisfactory for this specific condition, which implies additional investigation.

Reducing delamination risk with response surface methodology-supported drilling analysis for Nomex® aramid fiber composites

A New Strategy of Carbon Fiber Reinforced Plastic Drilling Evaluation Using Thermal Measurement

Cutting parameters optimization of hybrid fiber composite during drilling

Optimization of drilling parameters to minimize delamination in (PEKK/CFRP) thermoplastic polymer matrix composites for aerospace applications

Influence of Drilling Parameters on the Delamination and Surface Roughness of Insulative-Coated Glass/Carbon-Hybrid Composite

Effect of Drilling Force on Delamination of Abaca/Kenaf/Carbon Fiber Reinforced Hybrid Composite

Optimization of Drilling Parameters on Delamination and Burr Formation in Drilling of Neat CFRP and Hybrid CFRP Nano-Composites

Thermo-Mechanical and Delamination Properties in Drilling GFRP Composites by Various Drill Angles

Investigation of Damage Reduction When Dry-Drilling Aramid Fiber-Reinforced Plastics Based on a Three-Point Step Drill

Effects of drilling parameters on delamination of kenaf-glass fibre reinforced unsaturated polyester composites

Assessment of thrust force, delamination and temperature during drilling of basalt fiber-reinforced composite with different drill geometries

Investigation on carbon fiber-reinforced polymer combined with graphene nanoparticles subjected to drilling operation using response surface methodology and non-dominated sorting genetic algorithm-II

Experimental Investigation of drill tool types on delamination error in drilling of CFRP

Investigation of delamination and surface quality of machined holes in drilling of multiwalled carbon nanotube doped epoxy/carbon fiber reinforced polymer nanocomposite

Assessment and analysis of drilling-induced damage in jute/palm date fiber-reinforced polyester hybrid composite

Comprehensive investigation of cutting mechanisms and hole quality in dry drilling woven aramid fibre–reinforced plastic with typical tools

Optimization of drilling delamination behavior of GFRP/clay nano-composites using RSM and GRA methods

Optimizing Process Parameters in Drilling of CFRP Laminates: A Combined MOORA–TOPSIS–VIKOR Approach

Effect of Drilling Parameters and Tool Diameter on Delamination and Thrust Force in the Drilling of High-Performance Glass/Epoxy Composites for Aerospace Structures with a New Design Drill

Delamination assessment and prediction in ultrasonic-assisted drilling of laminated hybrid composites

Optimization for drilling process of metal-composite aeronautical structures